Greene Street Pool Tavern

Observed vape on top of surface of food prep area. 511-6-1.03(5)(k)1&2 - Eating, Drinking, or Using Tobacco (C) (k) Hygienic Practices.

1. Employees shall not use any form of tobacco products, or electronic devices that simulate tobacco smoking, while engaged in food preparation or service, nor while in areas used for equipment or utensil washing and storage, food preparation or food storage. Employees shall only use tobacco products or electronic devices that simulate tobacco smoking in approved designated areas.

2. Employees shall consume food only in approved designated areas separate from food preparation and serving areas, equipment or utensil areas and food storage areas. However, drinking from a single service beverage cup with a secure lid and straw that is handled to prevent contamination of the employee’s hands, the container, exposed food, clean equipment, utensils and linens, unwrapped single-service and single-use articles will be allowed.

PIC was notified. Education was provided.

Observed handwash sink without soap. 511-6-1.07(3)(a) - Handwashing Cleanser, Availability (Pf) (3) Numbers and Capacities.

(a) Handwashing Cleanser, Availability. Each handwashing sink or group of two adjacent handwashing sinks shall be provided with a supply of hand cleaning liquid, powder, or bar soap. Pf

PIC was notified. Education was provided.

Observed no written procedures for responding to contamination events. 511-6-1.03(6) - Clean-up of Vomiting and Diarrheal Events(Pf) (6) Responding To Contamination Events. A food establishment shall have written procedures for employees to follow and an EPA registered disinfectant effective against Norovirus available on-site at the food service establishment when responding to vomiting or diarrheal events that involve the discharge of vomitus or fecal matter onto surfaces in the food service establishment. The procedures shall address the specific actions employees must take to minimize the spread of contamination and the exposure of employees, consumers, food, and surfaces to vomitus or fecal matter.Pf

PIC was notified. Education was provided.

Observed most current health inspection not posted. 511-6-1.02(1)(d) - Displaying of the Inspection Report (C)

1. The most current inspection report shall be prominently displayed in public view at all times, within fifteen feet of the front or primary public door and between five feet and seven feet from the floor and in an area where it can be read at a distance of one foot away.

2. Food service establishments with drive-thru windows will post the current inspection report, and also have the inspection report posted so that a minimum of the top one-third of a copy of the current inspection report is visible through each window allowing customers to easily read the score, date of inspection and establishment information.

3. At food service establishments with no primary or public door, the current inspection report shall be prominently displayed at all times where the documents can be read by the public from a distance of one foot away. If requirements of this paragraph are not possible because of physical restrictions, a location will be determined as approved by the Health Authority.

4. The most current inspection report for mobile food service units and extended food service units issued by the local Health Authority having jurisdiction for its inspections shall be prominently displayed in public view during all hours of operation. Such inspection reports shall be prominently displayed at the point of service where the documents can be read by the public from a distance of one foot away.

5. A food service establishment inspection report addendum need not be displayed, but shall be made available by the food service establishment to the public upon request.

PIC was notified. Education was provided.

Observed boxes of cups and toilet paper being stored on the floor in storage area. 511-6-1.05(10)(e)1&3 - Single-Service/Single-Use items stored 6" off floor in clean, dry location (C) (e) Equipment, Utensils, Linens, and Single-Service and Single-Use Articles.

1. Except as specified in paragraph 4 of this subsection, cleaned equipment and utensils, laundered linens, and single-service and single-use articles shall be stored:

(i) In a clean, dry location;

(ii) Where they are not exposed to splash, dust, or other contamination; and

(iii) At least 6 inches (15 centimeters) above the floor. 3. Single-service and single-use articles shall be stored as specified under paragraph 1 of this subsection and shall be kept in the original protective package or stored by using other means that afford protection from contamination until used.

PIC was notified. Education was provided.

Observed pizza uncovered in RIF. 511-6-1.04(4)(c)1(iv) - Packaged & Unpackaged Food, food stored covered(C) (iv) Except as specified under paragraph 2. of this subsection and when cooling as specified in DPH Rule 511-6-1-.04(6)(e)2.(ii), storing the food in packages, covered containers, or wrappings, except for loosely covered or uncovered containers in which food is being cooled if protected from overhead contamination

PIC was notified. Education was provided.

Observed mold like substance in ice machine. 511-6-1.05(7)(b) - Food Contact Surfaces and Utensils - Cleaning Frequency (P, C) (b) Equipment Food-Contact Surfaces and Utensils.

1. Equipment food-contact surfaces and utensils shall be cleaned:

(i) Before each use with a different type of raw animal food such as beef, fish, lamb, pork, or poultry. It does not apply if the food-contact surface or utensil is in contact with a succession of different types of raw meat and raw poultry each requiring a higher cooking temperature as specified under DPH Rule 511-6-1.04(5)(a) than the previous type such as preparing raw pork followed by cutting raw poultry on the same cutting board; P

(ii) Each time there is a change from working with raw foods to working with ready-to-eat foods; P

(iii) Between uses with raw fruits and vegetables and with Time/Temperature Control for safety food; P

(iv) Before using or storing a food temperature measuring device; P and

(v) At any time during the operation when contamination may have occurred. P

2. Except as specified in paragraph 3 of this subsection, if used with time/temperature control for safety food, equipment food-contact surfaces and utensils shall be cleaned at least every 4 hours throughout the day. P

3. Surfaces of utensils and equipment contacting time/temperature control for safety food may be cleaned less frequently than every 4 hours if:

(i) In storage, containers of time/temperature control for safety food and their contents are maintained at temperatures specified under DPH Rule 511-6-1-.04 and the containers are cleaned when they are empty;

(ii) Utensils and equipment are used to prepare food in a refrigerated room or area that is maintained at one of the temperatures in the following chart and:

(I) The utensils and equipment are cleaned at the frequency in the following chart that corresponds to the temperature:

Temperature Cleaning Frequency

41ºF (5.0ºC) or less 24 hours

41ºF - 45ºF (>5.0ºC - 7.2ºC) 20 hours

45ºF - 50ºF (>7.2ºC - 10.0ºC) 16 hours

50ºF - 55ºF (>10.0ºC - 12.8ºC) 10 hours

and

(II) The cleaning frequency based on the ambient temperature of the refrigerated room or area is documented in the food service establishment.

(iii) Temperature measuring devices are maintained in contact with food, such as when left in a container of deli food or in a roast, held at temperatures specified under DPH Rule 511-6-1- .04;

(iv) Equipment is used for storage of packaged or unpackaged food, such as a reach-in refrigerator, and the equipment is cleaned at a frequency necessary to preclude accumulation of soil residues;

(v) The cleaning schedule is approved based on consideration of:

(I) Characteristics of the equipment and its use,

(II) The type of food involved,

(III) The amount of food residue accumulation, and

(IV) The temperature at which the food is maintained during the operation and the potential for the rapid and progressive multiplication of pathogenic or toxigenic microorganisms that are capable of causing foodborne disease; or

(vi) In-use utensils are intermittently stored in a container of water in which the water is maintained at 135ºF (57ºC) or more and the utensils and container are cleaned at least every 24 hours or at a frequency necessary to preclude accumulation of soil residues.

4. Dining counters and table-tops shall be cleaned and sanitized routinely after removing all soiled tableware and food trays shall be cleaned and sanitized after each use by one of the following methods:

(i) A two step method in which one cloth, rinsed in sanitizing solution is used to clean food debris from the surface and a second cloth in separate sanitizing solution is used to rinse;

(ii) Sanitizing solution is sprayed onto the surface and the surface is then wiped clean with a disposable towel;

(iii) If used for cleaning and sanitizing, single-use disposable sanitizer wipes shall be used in accordance with EPA-registered label use instructions; or

(iv) Other methods approved by the Health Authority.

(v) Food trays may be cleaned and sanitized the same as table ware.

5. Except when dry cleaning methods are used as specified under subsection (7)(e) of this Rule, surfaces of utensils and equipment contacting food that is not time/temperature control for safety food shall be cleaned:

(i) At any time when contamination may have occurred;

(ii) At least every 24 hours for iced tea dispensers including nozzles and consumer self-service utensils such as tongs, scoops, or ladles;

(iii) Before restocking consumer self-service equipment and utensils such as condiment dispensers and display containers; and

(iv) In equipment such as ice bins and beverage dispensing nozzles and enclosed components of equipment such as ice makers, cooking oil storage tanks and distribution lines, beverage and syrup dispensing lines or tubes, coffee bean grinders, and water vending equipment:

(I) At a frequency specified by the manufacturer; or

(II) Absent manufacturer specifications, at a frequency necessary to preclude accumulation of soil or mold.

PIC was notified. Education was provided.

Observed cheese in RIC with green moldlike substance. 511-6-1.04(1) - Safe, unadulterated and Honestly Presented (P) (1) Condition. Food shall be safe, unadulterated, and honestly presented

PIC was notified. Education was provided.

Observed handwash sink without soap. 511-6-1.07(3)(a) - Handwashing Cleanser, Availability (Pf) (3) Numbers and Capacities.

(a) Handwashing Cleanser, Availability. Each handwashing sink or group of two adjacent handwashing sinks shall be provided with a supply of hand cleaning liquid, powder, or bar soap. Pf

PIC was notified. Education was provided.

Observed pizza uncovered in RIF. 511-6-1.04(4)(c)1(iv) - Packaged & Unpackaged Food, food stored covered(C) (iv) Except as specified under paragraph 2. of this subsection and when cooling as specified in DPH Rule 511-6-1-.04(6)(e)2.(ii), storing the food in packages, covered containers, or wrappings, except for loosely covered or uncovered containers in which food is being cooled if protected from overhead contamination

PIC was notified. Education was provided.

Observed mold like substance in ice machine. 511-6-1.05(7)(b) - Food Contact Surfaces and Utensils - Cleaning Frequency (P, C) (b) Equipment Food-Contact Surfaces and Utensils.

1. Equipment food-contact surfaces and utensils shall be cleaned:

(i) Before each use with a different type of raw animal food such as beef, fish, lamb, pork, or poultry. It does not apply if the food-contact surface or utensil is in contact with a succession of different types of raw meat and raw poultry each requiring a higher cooking temperature as specified under DPH Rule 511-6-1.04(5)(a) than the previous type such as preparing raw pork followed by cutting raw poultry on the same cutting board; P

(ii) Each time there is a change from working with raw foods to working with ready-to-eat foods; P

(iii) Between uses with raw fruits and vegetables and with Time/Temperature Control for safety food; P

(iv) Before using or storing a food temperature measuring device; P and

(v) At any time during the operation when contamination may have occurred. P

2. Except as specified in paragraph 3 of this subsection, if used with time/temperature control for safety food, equipment food-contact surfaces and utensils shall be cleaned at least every 4 hours throughout the day. P

3. Surfaces of utensils and equipment contacting time/temperature control for safety food may be cleaned less frequently than every 4 hours if:

(i) In storage, containers of time/temperature control for safety food and their contents are maintained at temperatures specified under DPH Rule 511-6-1-.04 and the containers are cleaned when they are empty;

(ii) Utensils and equipment are used to prepare food in a refrigerated room or area that is maintained at one of the temperatures in the following chart and:

(I) The utensils and equipment are cleaned at the frequency in the following chart that corresponds to the temperature:

Temperature Cleaning Frequency

41ºF (5.0ºC) or less 24 hours

41ºF - 45ºF (>5.0ºC - 7.2ºC) 20 hours

45ºF - 50ºF (>7.2ºC - 10.0ºC) 16 hours

50ºF - 55ºF (>10.0ºC - 12.8ºC) 10 hours

and

(II) The cleaning frequency based on the ambient temperature of the refrigerated room or area is documented in the food service establishment.

(iii) Temperature measuring devices are maintained in contact with food, such as when left in a container of deli food or in a roast, held at temperatures specified under DPH Rule 511-6-1- .04;

(iv) Equipment is used for storage of packaged or unpackaged food, such as a reach-in refrigerator, and the equipment is cleaned at a frequency necessary to preclude accumulation of soil residues;

(v) The cleaning schedule is approved based on consideration of:

(I) Characteristics of the equipment and its use,

(II) The type of food involved,

(III) The amount of food residue accumulation, and

(IV) The temperature at which the food is maintained during the operation and the potential for the rapid and progressive multiplication of pathogenic or toxigenic microorganisms that are capable of causing foodborne disease; or

(vi) In-use utensils are intermittently stored in a container of water in which the water is maintained at 135ºF (57ºC) or more and the utensils and container are cleaned at least every 24 hours or at a frequency necessary to preclude accumulation of soil residues.

4. Dining counters and table-tops shall be cleaned and sanitized routinely after removing all soiled tableware and food trays shall be cleaned and sanitized after each use by one of the following methods:

(i) A two step method in which one cloth, rinsed in sanitizing solution is used to clean food debris from the surface and a second cloth in separate sanitizing solution is used to rinse;

(ii) Sanitizing solution is sprayed onto the surface and the surface is then wiped clean with a disposable towel;

(iii) If used for cleaning and sanitizing, single-use disposable sanitizer wipes shall be used in accordance with EPA-registered label use instructions; or

(iv) Other methods approved by the Health Authority.

(v) Food trays may be cleaned and sanitized the same as table ware.

5. Except when dry cleaning methods are used as specified under subsection (7)(e) of this Rule, surfaces of utensils and equipment contacting food that is not time/temperature control for safety food shall be cleaned:

(i) At any time when contamination may have occurred;

(ii) At least every 24 hours for iced tea dispensers including nozzles and consumer self-service utensils such as tongs, scoops, or ladles;

(iii) Before restocking consumer self-service equipment and utensils such as condiment dispensers and display containers; and

(iv) In equipment such as ice bins and beverage dispensing nozzles and enclosed components of equipment such as ice makers, cooking oil storage tanks and distribution lines, beverage and syrup dispensing lines or tubes, coffee bean grinders, and water vending equipment:

(I) At a frequency specified by the manufacturer; or

(II) Absent manufacturer specifications, at a frequency necessary to preclude accumulation of soil or mold.

PIC was notified. Education was provided.

Observed cleaning spray in prep surface in main kitchen. 511-6-1.07(6)(c) - Storage, Separation (P) (c) Storage, Separation. Poisonous or toxic materials shall be stored so they cannot contaminate food, equipment, utensils, linens, and single-service and single-use articles by:

1. Separating the poisonous or toxic materials by spacing or partitioning; P and

2. Locating the poisonous or toxic materials in an area that is not above food, equipment, utensils, linens, and single-service or single-use articles. This requirement does not apply to equipment and utensil cleaners and sanitizers that are stored in warewashing areas for availability and convenience if the materials are stored to prevent contamination of food, equipment, utensils, linens, and single-service and single-use articles.

PIC was notified. Education was provided.

Observed fortune cookies stored on the floor in main kitchen. 511-6-1.04(4)(q) - Food Storage (C) (q) Food Storage.

1. Except as specified in paragraphs 2 and 3 of this subsection, food shall be protected from contamination by storing the food:

(i) In a clean, dry location;

(ii) Where it is not exposed to splash, dust, or other contamination; and

(iii) At least 6 inches (15 cm) above the floor.

2. Food in packages and working containers may be stored less than 6 inches (15 cm) above the floor on case lot handling equipment if the equipment can be moved by hand or by conveniently available apparatuses such as hand trucks and forklifts.

3. Pressurized beverage containers, cased food in waterproof containers such as bottles or cans, and milk containers in plastic crates may be stored on a floor that is clean and not exposed to floor moisture.

PIC was notified. Education was provided.

Observed plates, straws, and lids being stored on the floor in main kitchen. 511-6-1.05(10)(e)1&3 - Single-Service/Single-Use items stored 6" off floor in clean, dry location (C) (e) Equipment, Utensils, Linens, and Single-Service and Single-Use Articles.

1. Except as specified in paragraph 4 of this subsection, cleaned equipment and utensils, laundered linens, and single-service and single-use articles shall be stored:

(i) In a clean, dry location;

(ii) Where they are not exposed to splash, dust, or other contamination; and

(iii) At least 6 inches (15 centimeters) above the floor. 3. Single-service and single-use articles shall be stored as specified under paragraph 1 of this subsection and shall be kept in the original protective package or stored by using other means that afford protection from contamination until used.

PIC was notified. Education was provided.

Observed pizza uncovered in RIF. 511-6-1.04(4)(c)1(iv) - Packaged & Unpackaged Food, food stored covered(C) (iv) Except as specified under paragraph 2. of this subsection and when cooling as specified in DPH Rule 511-6-1-.04(6)(e)2.(ii), storing the food in packages, covered containers, or wrappings, except for loosely covered or uncovered containers in which food is being cooled if protected from overhead contamination

PIC was notified. Education was provided.

Observed mold like substance in ice machine. 511-6-1.05(7)(b) - Food Contact Surfaces and Utensils - Cleaning Frequency (P, C) (b) Equipment Food-Contact Surfaces and Utensils.

1. Equipment food-contact surfaces and utensils shall be cleaned:

(i) Before each use with a different type of raw animal food such as beef, fish, lamb, pork, or poultry. It does not apply if the food-contact surface or utensil is in contact with a succession of different types of raw meat and raw poultry each requiring a higher cooking temperature as specified under DPH Rule 511-6-1.04(5)(a) than the previous type such as preparing raw pork followed by cutting raw poultry on the same cutting board; P

(ii) Each time there is a change from working with raw foods to working with ready-to-eat foods; P

(iii) Between uses with raw fruits and vegetables and with Time/Temperature Control for safety food; P

(iv) Before using or storing a food temperature measuring device; P and

(v) At any time during the operation when contamination may have occurred. P

2. Except as specified in paragraph 3 of this subsection, if used with time/temperature control for safety food, equipment food-contact surfaces and utensils shall be cleaned at least every 4 hours throughout the day. P

3. Surfaces of utensils and equipment contacting time/temperature control for safety food may be cleaned less frequently than every 4 hours if:

(i) In storage, containers of time/temperature control for safety food and their contents are maintained at temperatures specified under DPH Rule 511-6-1-.04 and the containers are cleaned when they are empty;

(ii) Utensils and equipment are used to prepare food in a refrigerated room or area that is maintained at one of the temperatures in the following chart and:

(I) The utensils and equipment are cleaned at the frequency in the following chart that corresponds to the temperature:

Temperature Cleaning Frequency

41ºF (5.0ºC) or less 24 hours

41ºF - 45ºF (>5.0ºC - 7.2ºC) 20 hours

45ºF - 50ºF (>7.2ºC - 10.0ºC) 16 hours

50ºF - 55ºF (>10.0ºC - 12.8ºC) 10 hours

and

(II) The cleaning frequency based on the ambient temperature of the refrigerated room or area is documented in the food service establishment.

(iii) Temperature measuring devices are maintained in contact with food, such as when left in a container of deli food or in a roast, held at temperatures specified under DPH Rule 511-6-1- .04;

(iv) Equipment is used for storage of packaged or unpackaged food, such as a reach-in refrigerator, and the equipment is cleaned at a frequency necessary to preclude accumulation of soil residues;

(v) The cleaning schedule is approved based on consideration of:

(I) Characteristics of the equipment and its use,

(II) The type of food involved,

(III) The amount of food residue accumulation, and

(IV) The temperature at which the food is maintained during the operation and the potential for the rapid and progressive multiplication of pathogenic or toxigenic microorganisms that are capable of causing foodborne disease; or

(vi) In-use utensils are intermittently stored in a container of water in which the water is maintained at 135ºF (57ºC) or more and the utensils and container are cleaned at least every 24 hours or at a frequency necessary to preclude accumulation of soil residues.

4. Dining counters and table-tops shall be cleaned and sanitized routinely after removing all soiled tableware and food trays shall be cleaned and sanitized after each use by one of the following methods:

(i) A two step method in which one cloth, rinsed in sanitizing solution is used to clean food debris from the surface and a second cloth in separate sanitizing solution is used to rinse;

(ii) Sanitizing solution is sprayed onto the surface and the surface is then wiped clean with a disposable towel;

(iii) If used for cleaning and sanitizing, single-use disposable sanitizer wipes shall be used in accordance with EPA-registered label use instructions; or

(iv) Other methods approved by the Health Authority.

(v) Food trays may be cleaned and sanitized the same as table ware.

5. Except when dry cleaning methods are used as specified under subsection (7)(e) of this Rule, surfaces of utensils and equipment contacting food that is not time/temperature control for safety food shall be cleaned:

(i) At any time when contamination may have occurred;

(ii) At least every 24 hours for iced tea dispensers including nozzles and consumer self-service utensils such as tongs, scoops, or ladles;

(iii) Before restocking consumer self-service equipment and utensils such as condiment dispensers and display containers; and

(iv) In equipment such as ice bins and beverage dispensing nozzles and enclosed components of equipment such as ice makers, cooking oil storage tanks and distribution lines, beverage and syrup dispensing lines or tubes, coffee bean grinders, and water vending equipment:

(I) At a frequency specified by the manufacturer; or

(II) Absent manufacturer specifications, at a frequency necessary to preclude accumulation of soil or mold.

PIC was notified. Education was provided.

Observed cooked beef without a date in RIC. 511-6-1.04(6)(g) - Ready-To-Eat Time/Temperature Control for Safety Food, Date Marking (Pf) (g) Ready-to-Eat Time/Temperature Control for Safety Food, Date Marking

1. Except when packaging food using a reduced oxygen packaging method, and except as specified in paragraphs 4 and 5 of this subsection, refrigerated, ready-to-eat, time/temperature control for safety food prepared and held in a food establishment for more than 24 hours shall be clearly marked to indicate the date or day by which the food shall be consumed on the premises, sold, or discarded, when held at a temperature of 41°F (5°C) or below for a maximum of 7 days. The day of preparation shall be counted as Day 1. Pf

2. Except as specified in paragraphs 4 through 6 of this subsection, refrigerated, ready-to-eat, time/temperature control for safety food prepared and packaged by a food processing plant shall be clearly marked, at the time the original container is opened in a food service establishment and if the food is held for more than 24 hours, to indicate the date or day by which the food shall be consumed on the premises, sold, or discarded, when held at a temperature of 41°F (5°C) or below for a maximum of 7 days after the original container is opened. The day the original container is opened in the food service establishment shall be counted as Day 1, except, the day or date marked by the food service establishment may not exceed a manufacturer’s use by date if the manufacturer determined the use-by date based on food safety; Pf

3. A refrigerated, ready-to-eat, time/temperature control for safety food ingredient or a portion of a refrigerated, ready-to-eat, time/temperature control for safety food that is subsequently combined with additional ingredients or portions of food shall retain the date marking of the earliest-prepared or first-prepared ingredient. Pf

4. A date marking system that meets the criteria stated in paragraphs 1 and 2 of this subsection may include:

(i) Using a method approved by the Health Authority for refrigerated, ready-to-eat time / temperature control for safety food that is frequently rewrapped, such as lunchmeat or a roast, or for which date marking is impractical, such as soft serve mix or milk in a dispensing machine;

(ii) Marking the date or day of preparation, with a procedure to discard the food on or before the last date or day by which the food must be consumed on the premises, sold, or discarded;

(iii) Marking the date or day the original container is opened in a food service establishment, with a procedure to discard the food on or before the last date or day by which the food must be consumed on the premises, sold, or discarded; or

(iv) Using calendar dates, days of the week, color-coded marks, or other effective marking methods, provided that the marking system is disclosed to the Health Authority upon request.

5. The requirements in paragraphs 1 and 2 of this subsection do not apply to individual meal portions served or repackaged for sale from a bulk container upon a consumer’s request.

6. The requirements in paragraphs 1 and 2 of this subsection do not apply to shellstock.

7. The requirement in paragraph 2 of this subsection does not apply to the following foods prepared and packaged by a food processing plant inspected by a Health Authority:

(i) Deli salads, such as ham salad, seafood salad, chicken salad, egg salad, pasta salad, potato salad, and macaroni salad, manufactured in accordance with 21 CFR 110 Current good manufacturing practice in manufacturing, packing, or holding human food;

(ii) Hard cheeses containing not more than 39% moisture as defined in 21 CFR 133 Cheeses and related cheese products, such as cheddar, gruyere, parmesan and reggiano, and romano;

(iii) Semi-soft cheeses containing more than 39% moisture, but not more than 50% moisture, as defined in 21 CFR 133 Cheeses and related cheese products, such as blue, edam, gorgonzola, gouda, and monterey jack;

(iv) Cultured dairy products as defined in 21 CFR 131 Milk and cream, such as yogurt, sour cream, and buttermilk;

(v) Preserved fish products, such as pickled herring and dried or salted cod, and other acidified fish products defined in 21 CFR 114 Acidified foods;

(vi) Shelf stable, dry fermented sausages, such as pepperoni and Genoa salami; and

(vii) Shelf stable salt-cured products, such as prosciutto and Parma ham.

PIC was notified. Education was provided.

Observed bucket of water stored in the hand wash sink in kitchen. 511-6-1.06(2)(o) - Using a Handwashing Sink- Operation & maintenance (Pf) (o) Using a Handwashing Sink.

1. A handwashing sink shall be maintained so that it is accessible at all times for employee use. Pf

2. A handwashing facility may not be used for purposes other than handwashing.

PIC was notified. Education was provided.

Observed pizza and chicken in RIC without a date. 511-6-1.04(6)(g) - Ready-To-Eat Time/Temperature Control for Safety Food, Date Marking (Pf) (g) Ready-to-Eat Time/Temperature Control for Safety Food, Date Marking

1. Except when packaging food using a reduced oxygen packaging method, and except as specified in paragraphs 4 and 5 of this subsection, refrigerated, ready-to-eat, time/temperature control for safety food prepared and held in a food establishment for more than 24 hours shall be clearly marked to indicate the date or day by which the food shall be consumed on the premises, sold, or discarded, when held at a temperature of 41°F (5°C) or below for a maximum of 7 days. The day of preparation shall be counted as Day 1. Pf

2. Except as specified in paragraphs 4 through 6 of this subsection, refrigerated, ready-to-eat, time/temperature control for safety food prepared and packaged by a food processing plant shall be clearly marked, at the time the original container is opened in a food service establishment and if the food is held for more than 24 hours, to indicate the date or day by which the food shall be consumed on the premises, sold, or discarded, when held at a temperature of 41°F (5°C) or below for a maximum of 7 days after the original container is opened. The day the original container is opened in the food service establishment shall be counted as Day 1, except, the day or date marked by the food service establishment may not exceed a manufacturer’s use by date if the manufacturer determined the use-by date based on food safety; Pf

3. A refrigerated, ready-to-eat, time/temperature control for safety food ingredient or a portion of a refrigerated, ready-to-eat, time/temperature control for safety food that is subsequently combined with additional ingredients or portions of food shall retain the date marking of the earliest-prepared or first-prepared ingredient. Pf

4. A date marking system that meets the criteria stated in paragraphs 1 and 2 of this subsection may include:

(i) Using a method approved by the Health Authority for refrigerated, ready-to-eat time / temperature control for safety food that is frequently rewrapped, such as lunchmeat or a roast, or for which date marking is impractical, such as soft serve mix or milk in a dispensing machine;

(ii) Marking the date or day of preparation, with a procedure to discard the food on or before the last date or day by which the food must be consumed on the premises, sold, or discarded;

(iii) Marking the date or day the original container is opened in a food service establishment, with a procedure to discard the food on or before the last date or day by which the food must be consumed on the premises, sold, or discarded; or

(iv) Using calendar dates, days of the week, color-coded marks, or other effective marking methods, provided that the marking system is disclosed to the Health Authority upon request.

5. The requirements in paragraphs 1 and 2 of this subsection do not apply to individual meal portions served or repackaged for sale from a bulk container upon a consumer’s request.

6. The requirements in paragraphs 1 and 2 of this subsection do not apply to shellstock.

7. The requirement in paragraph 2 of this subsection does not apply to the following foods prepared and packaged by a food processing plant inspected by a Health Authority:

PIC was notified. Education was provided.

Observed plates being stored on the floor in main kitchen. 511-6-1.05(10)(e)1&3 - Single-Service/Single-Use items stored 6" off floor in clean, dry location (C) (e) Equipment, Utensils, Linens, and Single-Service and Single-Use Articles.

1. Except as specified in paragraph 4 of this subsection, cleaned equipment and utensils, laundered linens, and single-service and single-use articles shall be stored:

(i) In a clean, dry location;

(ii) Where they are not exposed to splash, dust, or other contamination; and

(iii) At least 6 inches (15 centimeters) above the floor. 3. Single-service and single-use articles shall be stored as specified under paragraph 1 of this subsection and shall be kept in the original protective package or stored by using other means that afford protection from contamination until used.

PIC was notified. Education was provided.