Stonecrest, DeKalb County

SPICE HOUSE

2617 PANOLA RD LITHONIA, GA 30058

Food
Latest score
73
May 4, 2026
City
Stonecrest
County
DeKalb
Inspections
11

Score history

Inspection scores over time for this facility.

Inspection history

Georgia inspection history is score-based, with violations grouped under each recorded inspection.

May 4, 2026

Routine

Score: 7313 violations

6-1A - proper cold holding temperatures

Regulation: 511-6-1.04(6)(f) - time/temperature control for safety; cold holding (p)

9 ptsCorrected: YesRepeat: Yes

Observed shelled egg 45F, cream cheese- 44F and butter 46F stored in reach in cooler not maintaining a TCS food temp of 41F or below. Ambient of reach in cooler is 40F. COS: All items were discarded by PIC and advised not to over stock the reach in cooler.

6-1B - proper hot holding temperatures

Regulation: 511-6-1.04(6)(f) - time/temperature control for safety; hot holding (p)

9 ptsCorrected: YesRepeat: No

Observed jerk chicken 110F, Mashed potatoes 90F, cabbage 80F stored at the steamtable not maintaining a TCS food temp of 135F or above. COS: Cabbage and Mashed potatoes were discarded by PIC. Jerk chicken was reheated to read 194F. C/A: 511-6-1.04(6)(f) - Time/Temperature Control for Safety; Hot Holding (P) (f) Time/Temperature Control for Safety Food, Hot and Cold Holding. Except during preparation, cooking, or cooling, or when time is used as the public health control, time/temperature control for safety food shall be maintained at 41°F (5°C) or below or 135°F (57°C) or above, except that roasts cooked to a temperature and for a time specified in subsection (5)(a)2 of this Rule and reheated using the same temperature and time conditions as cooking may be held at a temperature of 130°F (54°C) or above. P

2-2D - adequate handwashing facilities supplied & accessible

Regulation: 511-6-1.06(2)(o) - using a handwashing sink- operation & maintenance (pf)

4 ptsCorrected: YesRepeat: No

Observed cutting board with lemons stored in hand sink in main kitchen. Cutting board and lemons were moved to dish pit. C/A: 511-6-1.06(2)(o) - Using a Handwashing Sink- Operation & maintenance (Pf) (o) Using a Handwashing Sink.

  1. A handwashing sink shall be maintained so that it is accessible at all times for employee use. Pf

  2. A handwashing facility may not be used for purposes other than handwashing. Pf

  3. An automatic handwashing facility shall be used in accordance with manufacturer’s instructions. Pf

4-2B - food-contact surfaces: cleaned & sanitized

Regulation: 511-6-1.05(7)(b) - food contact surfaces and utensils - cleaning frequency (p, c)

4 ptsCorrected: YesRepeat: No

Observed pink matter on the ice board in direct contact with the ice. Observed brown and pick matter inside the soda gun nozzle in direct contact with soda. Ice was burned while inspector was onsite. Ice machine was cleaned and sanitized before placing back in service. Soda nozzle was deep cleaned while inspector was onsite. C/A: 511-6-1.05(7)(b) - Food Contact Surfaces and Utensils - Cleaning Frequency (P, C) (b) Equipment Food-Contact Surfaces and Utensils. 5. Except when dry cleaning methods are used as specified under subsection (7)(e) of this Rule, surfaces of utensils and equipment contacting food that is not time/temperature control for safety food shall be cleaned:

(i) At any time when contamination may have occurred;

(ii) At least every 24 hours for iced tea dispensers including nozzles and consumer self-service utensils such as tongs, scoops, or ladles;

(iii) Before restocking consumer self-service equipment and utensils such as condiment dispensers and display containers; and

(iv) In equipment such as ice bins and beverage dispensing nozzles and enclosed components of equipment such as ice makers, cooking oil storage tanks and distribution lines, beverage and syrup dispensing lines or tubes, coffee bean grinders, and water vending equipment

4-2B - food-contact surfaces: cleaned & sanitized

Regulation: 511-6-1.05(6)(n) - manual and mechanical warewashing equipment, chemical sanitization-temperature, ph, concentration, hardness (p,pf)

4 ptsCorrected: YesRepeat: No

Observed the dish machine being washed with no measurable amount of sanitizer. COS: Dish machine was placed in out of order status until servied. C/A:511-6-1.05(6)(n) - Manual and Mechanical Warewashing Equipment, Chemical Sanitization-Temperature, pH, Concentration, Hardness (P,Pf) (n) Manual and Mechanical Warewashing Equipment, Chemical Sanitization - Temperature, pH, Concentration, and Hardness. A chemical sanitizer used in a sanitizing solution for a manual or mechanical operation at contact times specified under subsection (8)(b)3 of this Rule shall meet the requirements specified in DPH Rule 511-6-1-.07(6)(g), shall be used in accordance with the Environmental Protection Agency (EPA)-registered label use instructions P, and shall be used as follows:

  1. A chlorine solution shall have a minimum temperature based on the concentration and pH of the solution as listed in the following chart; P

Concentration Range Minimum Temperature

MG/L PH 10 or less oF (oC) PH 8 or less oF (oC)

25-49 120 (49) 120 (49)

50-99 100 (38) 75 (24)

100 55 (13) 55 (13)

11A - proper cooling methods used: adequate equipment for temperature control

Regulation: 511-6-1.04(6)(e) - cooling methods (pf, c)

3 ptsCorrected: YesRepeat: No

Observed large pan of cooked pasta noodles with lid on tight stored in walk in cooler to cool while inspector was onsite. COS: lids were removed and employee was educated on proper cooling methods. C/A: 511-6-1.04(6)(e) - Cooling Methods (Pf, C) (e) Cooling Methods.

  1. Cooling shall be accomplished in accordance with the time and temperature criteria specified under DPH Rule 511-6-1-.04(6)(d) by using one or more of the following methods depending on the type of food being cooled:

(i) Placing the food in shallow pans; Pf

(ii) Separating the food into smaller or thinner portions; Pf

(iii) Using rapid cooling equipment; Pf

(iv) Stirring the food in a container placed in an ice water bath; Pf

(v) Using containers that facilitate heat transfer; Pf

(vi) Adding ice as an ingredient; Pf or

(vii) Other effective methods. Pf

  1. When placed in cooling or cold holding equipment, food containers in which food is being cooled shall be:

(i) Arranged in the equipment to provide maximum heat transfer through the container walls; and

(ii) Loosely covered, or uncovered if protected from overhead contamination during the cooling period to facilitate heat transfer from the surface of the food.

11C - approved thawing methods used

Regulation: 511-6-1.04(6)(c) - thawing (c)

3 ptsCorrected: NoRepeat: No

Observed raw chicken at meat sink sitting in standing water. COS: Water was turned on to properly thaw chicken. C/A: 511-6-1.04(6)(c) - Thawing (C) (c) Thawing. Except as specified in paragraph 4 of this subsection, time/temperature control for safety food shall be thawed:

  1. Under refrigeration that maintains the food temperature at 41°F (5°C) or less; PF or

  2. Completely submerged under running water:

(i) At a water temperature of 70°F (21°C) or below, PF

(ii) With sufficient water velocity to agitate and float off loose particles in an overflow PF, and

(iii) For a period of time that does not allow thawed portions of ready-to-eat food to rise above 41°F (5°C), or

(iv) For a period of time that does not allow thawed portions of a raw animal food requiring cooking to be above 41°F (5°C), for more than 4 hours including:

(I) The time the food is exposed to the running water and the time needed for preparation for cooking PF, or

(II) The time it takes under refrigeration to lower the food temperature to 41°F (5°C) PF;

  1. As part of a cooking process if the food that is frozen is:

(i) Cooked as specified under subsections (5)(a)1 or 2 or (5)(b) or 5(e) of this Rule PF, or

(ii) Thawed in a microwave oven and immediately transferred to conventional cooking equipment, with no interruption in the process PF; or

  1. Using any procedure if a portion of frozen ready-to-eat food is thawed and prepared for immediate service in response to an individual consumer's order.

  2. Reduced oxygen packaged fish that bears a label indicating that it is to be kept frozen until time of use shall be removed from the reduced oxygen environment:

(i) Prior to its thawing under refrigeration that maintains the food temperature at 41°F (5°C) or less; or

(ii) Prior to, or immediately upon completion of its thawing, using procedures to completely submerge in running water as specified in paragraph 2 of this subsection.

12A - contamination prevented during food preparation, storage, display

Regulation: 511-6-1.04(4)(z) - miscellaneous sources of contamination (c)

3 ptsCorrected: NoRepeat: No

Observed dust debris build on fan in walk in cooler. TCS food items were covered at time of inspection Advised to have deep cleaned. C/A: 511-6-1.04(4)(z) - Miscellaneous Sources of Contamination (C) (z) Miscellaneous Sources of Contamination. Food shall be protected from contamination that may result from a factor or source not specified under paragraphs (a) through (y) of this subsection.

15A - food and nonfood-contact surfaces cleanable, properly designed, constructed, and used

Regulation: 511-6-1.05(1)(a) - materials, general requirements (p, c)

1 ptsCorrected: NoRepeat: No

Observed foil used to line the shelf in the main kitchen. Advised to have removed. C/A: 511-6-1.05(1)(a) - Materials, General Requirements (P, C) (1) Materials.

(a) General Requirements. Utensils and food-contact surfaces of equipment shall be made of materials that do not allow the migration of deleterious substances or impart colors, odors, or tastes to food and under normal use conditions, and shall be: P safe P, durable, corrosion-resistant, and nonabsorbent. In addition, materials shall be sufficient in weight and thickness to withstand repeated warewashing and shall be finished to have a smooth, easily cleanable surface. Materials shall be resistant to pitting, chipping, crazing, scratching, scoring, distortion and decomposition.

15C - nonfood-contact surfaces clean

Regulation: 511-6-1.05(7)(a)2,3 - equipment, food/nonfood-contact surfaces, and utensils, food-contact surfaces of cooking equipment & nonfood-contact surfaces free of accumulations (c)

1 ptsCorrected: YesRepeat: Yes

Observed inside of walk in cooler and walk in freezer unclean on the bottom with food debris build up and gaskets unclean.
Advised to have deep cleaned and increase cleaning frequency. COS: 511-6-1.05(7)(a)2,3 - Equipment, Food/Nonfood-Contact Surfaces, and Utensils, food-contact surfaces of cooking equipment & nonfood-contact surfaces free of accumulations (C) 2. The food-contact surfaces of cooking equipment and pans shall be kept free of encrusted grease deposits and other soil accumulations. 3. Nonfood-contact surfaces of equipment shall be kept free of an accumulation of dust, dirt, food residue, and other debris.

15C - nonfood-contact surfaces clean

Regulation: 511-6-1.05(7)(a)2,3 - equipment, food/nonfood-contact surfaces, and utensils, food-contact surfaces of cooking equipment & nonfood-contact surfaces free of accumulations (c)

1 ptsCorrected: YesRepeat: Yes

Observed inside of walk in cooler and walk in freezer unclean on the bottom with food debris build up and gaskets unclean.
Advised to have deep cleaned and increase cleaning frequency. COS: 511-6-1.05(7)(a)2,3 - Equipment, Food/Nonfood-Contact Surfaces, and Utensils, food-contact surfaces of cooking equipment & nonfood-contact surfaces free of accumulations (C) 2. The food-contact surfaces of cooking equipment and pans shall be kept free of encrusted grease deposits and other soil accumulations. 3. Nonfood-contact surfaces of equipment shall be kept free of an accumulation of dust, dirt, food residue, and other debris.

15A - food and nonfood-contact surfaces cleanable, properly designed, constructed, and used

Regulation: 511-6-1.05(6)(b) - cutting surfaces (c)

1 ptsCorrected: NoRepeat: No

Observed black substance build on the cutting board at the steamtable. Advised to have resurfaced or deep cleaned. C/A:511-6-1.05(6)(b) - Cutting Surfaces (C) (b) Cutting Surfaces. Surfaces such as cutting blocks and boards that are subject to scratching and scoring shall be resurfaced if they can no longer be effectively cleaned and sanitized, or discarded if they cannot be resurfaced.

15A - food and nonfood-contact surfaces cleanable, properly designed, constructed, and used

Regulation: 511-6-1.05(6)(b) - cutting surfaces (c)

1 ptsCorrected: NoRepeat: No

Observed black substance build on the cutting board at the steamtable. Advised to have resurfaced or deep cleaned. C/A:511-6-1.05(6)(b) - Cutting Surfaces (C) (b) Cutting Surfaces. Surfaces such as cutting blocks and boards that are subject to scratching and scoring shall be resurfaced if they can no longer be effectively cleaned and sanitized, or discarded if they cannot be resurfaced.

Feb 11, 2026

Followup

Score: 775 violations

2-1B - hands clean and properly washed

Regulation: 511-6-1.03(5)(c) - when to wash (p)

9 ptsCorrected: YesRepeat: No

Observed employee come from the restroom and proceed to go behind the bar to prepare a drink without washing hands. COS: Employee was educated on proper hand washing, complied, discarded drink, washed hands. C/A:511-6-1.03(5)(c) - When to Wash (P) (c) When to Wash. (ii) After using the toilet room; P

1-2B - certified food protection manager

Regulation: 511-6-1.03(3)(c) - certification documentation (pf)

4 ptsCorrected: NoRepeat: No

No Certified Food Manager Certificate posted for establishment at time of inspection. Corrective Action: 511-6-1.03(3)(a) - Food Safety Manager Certification (Pf) Food service establishments shall have in its employ a Certified Food Safety Manager (CFSM) as specified in paragraph (b) of this subsection to ensure food safety is being managed within the food service establishment during all hours of operation as specified within paragraph (d) of this subsection. Pf Current CFSM has been gone for more than 30 days. Given establishment 60 days to obtain CFSM.

2-2B - proper eating, tasting, drinking, or tobacco use

Regulation: 511-6-1.03(5)(k)1&2 - eating, drinking, or using tobacco (c)

4 ptsCorrected: YesRepeat: No

Observed employee eating an apple in main kitchen. COS: Employee discarded apple, washed hands and was educated on proper hand washing. C/A: 511-6-1.03(5)(k)1&2 - Eating, Drinking, or Using Tobacco (C) (k) Hygienic Practices. 2. Employees shall consume food only in approved designated areas separate from food preparation and serving areas, equipment or utensil areas and food storage areas. However, drinking from a single service beverage cup with a secure lid and straw that is handled to prevent contamination of the employee’s hands, the container, exposed food, clean equipment, utensils and linens, unwrapped single-service and single-use articles will be allowed.

4-2B - food-contact surfaces: cleaned & sanitized

Regulation: 511-6-1.05(7)(c) - cooking & baking equipment (c)

4 ptsCorrected: YesRepeat: No

Observed inside of microwave unclean with debris in direct contact with TCS foods. COS: Microwave was cleaned and sanitized while inspector was onsite. C/A: 511-6-1.05(7)(c) - Cooking & Baking Equipment (C) (c) Cooking and Baking Equipment. 2. The cavities and door seals of microwave ovens shall be cleaned at least every 24 hours by using the manufacturer's recommended cleaning procedure.

16A - hot and cold water available; adequate pressure

Regulation: 511-6-1.06(1)(g),(h) - water supply, capacity; pressure (pf)

2 ptsCorrected: NoRepeat: No

Hot water supply not maintained during peak periods. Advised to contact inspector once water heater is repaired. Email invoice to ashley.clark1@dph.ga.gov C/A:511-6-1.06(1)(g),(h) - Water Supply, Capacity; Pressure (Pf) (g) Capacity.

  1. The water source and system shall be of sufficient capacity to meet the peak water demands of the food service establishment. Pf

Jan 8, 2026

Routine

Score: 754 violations

4-1A - food separated and protected

Regulation: 511-6-1.04(4)(c)1(i)(ii)(iii)(v)(vi)(vii)(viii) - packaged & unpackaged food separation, packaging, and segregation (p, c)

9 ptsCorrected: YesRepeat: No

Observed raw chicken stored directly stored on top of raw fish in the small reach in cooler. Observed raw lamb chops stored directly on top of ready to eat cut lettuce. COS: Ready to eat cut lettuce and raw fish was discarded by PIC. Raw chicken was place in walk in freezer. Storage flyer was given to PIC. C/A:511-6-1.04(4)(c)1(i)(ii)(iii)(v)(vi)(vii)(viii) - Packaged & Unpackaged Food Separation, Packaging, and Segregation (P, C) (c) Packaged and Unpackaged Food - Separation, Packaging, and Segregation.

  1. Food shall be protected from cross contamination by:

(i) Except as specified in paragraph (i)(IV) of this subsection, separating raw animal foods during storage, preparation, holding, and display from:

(I) Raw ready-to-eat food including other raw animal food such as fish for sushi or molluscan shellfish, or other raw ready-to-eat food such as fruits and vegetables, P and

(II) Cooked ready-to-eat food; and P

(III) Fruits and vegetables before they are washed; P

(IV) Frozen, commercially processed and packaged raw animal food may be stored or displayed with or above frozen, commercially processed and packaged, ready-to-eat food.

(ii) Except when combined as ingredients, separating types of raw animal foods from each other such as beef, fish, lamb, pork, and poultry during storage, preparation, holding, and display by:

(I) Using separate equipment for each type, P or

(II) Arranging each type of food in equipment so that cross contamination of one type with another is prevented, P and

(III) Preparing each type of food at different times or in separate areas; P

(iii) Cleaning and sanitizing equipment and utensils;

(v) Cleaning hermetically sealed containers of food of visible soil before opening;

(vi) Protecting food containers that are received packaged together in a case or overwrap from cuts when the case or overwrap is opened;

(vii) Storing damaged, spoiled, or recalled food being held in the food service establishment separate from food, equipment, utensils, linens and single-service and single-use articles; or

(viii) Separating fruits and vegetables, before they are washed from ready-to-eat food.

6-1A - proper cold holding temperatures

Regulation: 511-6-1.04(6)(f) - time/temperature control for safety; cold holding (p)

9 ptsCorrected: YesRepeat: No

Observed raw chicken wings(45F), crab cakes(45F),shelled eggs(44F)stored in prep top reach in cooler and Raw cut chicken (45F) stored in walk in cooler not holding a TCS food temp of 41F or below. COS: All foods items were discarded by PIC. C/A: 511-6-1.04(6)(f) - Time/Temperature Control for Safety; Cold Holding (P) (f) Time/Temperature Control for Safety Food, Hot and Cold Holding. Except during preparation, cooking, or cooling, or when time is used as the public health control, time/temperature control for safety food shall be maintained at 41°F (5°C) or below or 135°F (57°C) or above, except that roasts cooked to a temperature and for a time specified in subsection (5)(a)2 of this Rule and reheated using the same temperature and time conditions as cooking may be held at a temperature of 130°F (54°C) or above. P

6-2 - proper date marking and disposition

Regulation: 511-6-1.04(6)(g) - ready-to-eat time/temperature control for safety food, date marking (pf)

4 ptsCorrected: YesRepeat: Yes

Observed multiple cooked TCS food items held for more than 24 hours without proper date markings. TCS foods were prepared 1/6/2026. Corrective Action: 511-6-1.04(6)(g) - Ready-To-Eat Time/Temperature Control for Safety Food, Date Marking (Pf) (g) Ready-to-Eat Time/Temperature Control for Safety Food, Date Marking

  1. Except when packaging food using a reduced oxygen packaging method, and except as specified in paragraphs 4 and 5 of this subsection, refrigerated, ready-to-eat, time/temperature control for safety food prepared and held in a food establishment for more than 24 hours shall be clearly marked to indicate the date or day by which the food shall be consumed on the premises, sold, or discarded, when held at a temperature of 41°F (5°C) or below for a maximum of 7 days. The day of preparation shall be counted as Day 1. Pf
  2. Except as specified in paragraphs 4 through 6 of this subsection, refrigerated, ready-to-eat, time/temperature control for safety food prepared and packaged by a food processing plant shall be clearly marked, at the time the original container is opened in a food service establishment and if the food is held for more than 24 hours, to indicate the date or day by which the food shall be consumed on the premises, sold, or discarded, when held at a temperature of 41°F (5°C) or below for a maximum of 7 days after the original container is opened. The day the original container is opened in the food service establishment shall be counted as Day 1, except, the day or date marked by the food service establishment may not exceed a manufacturer’s use by date if the manufacturer determined the use-by date based on food safety; Pf
  3. A refrigerated, ready-to-eat, time/temperature control for safety food ingredient or a portion of a refrigerated, ready-to-eat, time/temperature control for safety food that is subsequently combined with additional ingredients or portions of food shall retain the date marking of the earliest-prepared or first-prepared ingredient. Pf
  4. A date marking system that meets the criteria stated in paragraphs 1 and 2 of this subsection may include: (i) Using a method approved by the Health Authority for refrigerated, ready-to-eat time / temperature control for safety food that is frequently rewrapped, such as lunchmeat or a roast, or for which date marking is impractical, such as soft serve mix or milk in a dispensing machine; (ii) Marking the date or day of preparation, with a procedure to discard the food on or before the last date or day by which the food must be consumed on the premises, sold, or discarded; (iii) Marking the date or day the original container is opened in a food service establishment, with a procedure to discard the food on or before the last date or day by which the food must be consumed on the premises, sold, or discarded; or (iv) Using calendar dates, days of the week, color-coded marks, or other effective marking methods, provided that the marking system is disclosed to the Health Authority upon request. Corrected onsite: All ready to eat and TCS foods items stored for more than 24 hours were discarded. DPH JUST DATE IT Flyer was given to PIC

15C - nonfood-contact surfaces clean

1 ptsCorrected: NoRepeat: No

Observed inside of reach in coolers gaskets, outside of the crock pot unclean to sight and touch. Food debris observed in between gaskets. Corrective Action: 511-6-1.05(7)(a)2,3 - Equipment, Food/Nonfood-Contact Surfaces, and Utensils, food-contact surfaces of cooking equipment & nonfood-contact surfaces free of accumulations (C) 2. The food-contact surfaces of cooking equipment and pans shall be kept free of encrusted grease deposits and other soil accumulations. 3. Nonfood-contact surfaces of equipment shall be kept free of an accumulation of dust, dirt, food residue, and other debris.

Advised to have deep cleaned and increase cleaning frequency.

Jun 3, 2025

Routine

Score: 816 violations

2-2D - adequate handwashing facilities supplied & accessible

Regulation: 511-6-1.06(2)(o) - using a handwashing sink- operation & maintenance (pf)

4 ptsCorrected: YesRepeat: No

Observed plastic bowls in both hand sinks in main kitchen. C/A: 511-6-1.06(2)(o) - Using a Handwashing Sink- Operation & maintenance (Pf) (o) Using a Handwashing Sink.

  1. A handwashing sink shall be maintained so that it is accessible at all times for employee use. Pf

  2. A handwashing facility may not be used for purposes other than handwashing. Pf

  3. An automatic handwashing facility shall be used in accordance with manufacturer’s instructions. Pf COS: Both sinks were cleared and sanitized and advised hand sink shall remain free and clean at all times.

6-2 - proper date marking and disposition

Regulation: 511-6-1.04(6)(g) - ready-to-eat time/temperature control for safety food, date marking (pf)

4 ptsCorrected: YesRepeat: Yes

Observed multiple cooked TCS food items and held for more than 24 hours without proper date markings. TCS foods were prepared 3/8/2025. Corrective Action: 511-6-1.04(6)(g) - Ready-To-Eat Time/Temperature Control for Safety Food, Date Marking (Pf) (g) Ready-to-Eat Time/Temperature Control for Safety Food, Date Marking

  1. Except when packaging food using a reduced oxygen packaging method, and except as specified in paragraphs 4 and 5 of this subsection, refrigerated, ready-to-eat, time/temperature control for safety food prepared and held in a food establishment for more than 24 hours shall be clearly marked to indicate the date or day by which the food shall be consumed on the premises, sold, or discarded, when held at a temperature of 41°F (5°C) or below for a maximum of 7 days. The day of preparation shall be counted as Day 1. Pf

  2. Except as specified in paragraphs 4 through 6 of this subsection, refrigerated, ready-to-eat, time/temperature control for safety food prepared and packaged by a food processing plant shall be clearly marked, at the time the original container is opened in a food service establishment and if the food is held for more than 24 hours, to indicate the date or day by which the food shall be consumed on the premises, sold, or discarded, when held at a temperature of 41°F (5°C) or below for a maximum of 7 days after the original container is opened. The day the original container is opened in the food service establishment shall be counted as Day 1, except, the day or date marked by the food service establishment may not exceed a manufacturer’s use by date if the manufacturer determined the use-by date based on food safety; Pf

  3. A refrigerated, ready-to-eat, time/temperature control for safety food ingredient or a portion of a refrigerated, ready-to-eat, time/temperature control for safety food that is subsequently combined with additional ingredients or portions of food shall retain the date marking of the earliest-prepared or first-prepared ingredient. Pf

  4. A date marking system that meets the criteria stated in paragraphs 1 and 2 of this subsection may include:

(i) Using a method approved by the Health Authority for refrigerated, ready-to-eat time / temperature control for safety food that is frequently rewrapped, such as lunchmeat or a roast, or for which date marking is impractical, such as soft serve mix or milk in a dispensing machine;

(ii) Marking the date or day of preparation, with a procedure to discard the food on or before the last date or day by which the food must be consumed on the premises, sold, or discarded;

(iii) Marking the date or day the original container is opened in a food service establishment, with a procedure to discard the food on or before the last date or day by which the food must be consumed on the premises, sold, or discarded; or

(iv) Using calendar dates, days of the week, color-coded marks, or other effective marking methods, provided that the marking system is disclosed to the Health Authority upon request.

  1. The requirement in paragraph 2 of this subsection does not apply to the following foods prepared and packaged by a food processing plant inspected by a Health Authority:

(ii) Hard cheeses containing not more than 39% moisture as defined in 21 CFR 133 Cheeses and related cheese products, such as cheddar, gruyere, parmesan and reggiano, and romano;

Corrected onsite: All ready to eat and TCS foods items stored for more than 24 hours were discarded. DPH JUST DATE IT Flyer was given to PIC

11A - proper cooling methods used: adequate equipment for temperature control

Regulation: 511-6-1.04(6)(e) - cooling methods (pf, c)

3 ptsCorrected: YesRepeat: Yes

Observed cooked pasta, oxtails, mashed potato cooling with lids on tight. C/A: Corrective Action:511-6-1.04(6)(e) - Cooling Methods (Pf, C) (e) Cooling Methods.

  1. Cooling shall be accomplished in accordance with the time and temperature criteria specified under DPH Rule 511-6-1-.04(6)(d) by using one or more of the following methods depending on the type of food being cooled:

(i) Placing the food in shallow pans; Pf

(ii) Separating the food into smaller or thinner portions; Pf

(iii) Using rapid cooling equipment; Pf

(iv) Stirring the food in a container placed in an ice water bath; Pf

(v) Using containers that facilitate heat transfer; Pf

(vi) Adding ice as an ingredient; Pf or

(vii) Other effective methods. Pf

  1. When placed in cooling or cold holding equipment, food containers in which food is being cooled shall be:

(i) Arranged in the equipment to provide maximum heat transfer through the container walls; and

(ii) Loosely covered, or uncovered if protected from overhead contamination during the cooling period to facilitate heat transfer from the surface of the food.

Corrected onsite: TCS food items were just cooked. Inspector educated staff on proper cooling. Lids were removed to start proper cooling methods.

11D - thermometers provided and accurate

Regulation: 511-6-1.05(2)(k) - temperature measuring device (tmd), food - accuracy (pf)

3 ptsCorrected: NoRepeat: No

Observed no thermometer provided inside reach in coolers. C/A: 11-6-1.05(2)(k) - Temperature Measuring Device (TMD), Food - Accuracy (Pf) (k) Temperature Measuring Devices, Food.

  1. Food temperature measuring devices that are scaled only in Celsius or dually scaled in Celsius and Fahrenheit shall be accurate to ±1ºC in the intended range of use. Pf

  2. Food temperature measuring devices that are scaled only in Fahrenheit shall be accurate to ±2ºF in the intended range of use. Pf

Advised to purchase before next inspection.

18 - insects, rodents, and animals not present

Regulation: 511-6-1.07(5)(k) - controlling pests (pf, c)

3 ptsCorrected: NoRepeat: No

Observed gnats and flies in main dining area, behind bar and mop sink near rear door. Corrective Action: 511-6-1.07(5)(k) - Controlling Pests (Pf, C) (k) Controlling Pests. The presence of insects, rodents, and other pests shall be controlled to minimize their presence on the premises by:

  1. Routinely inspecting incoming shipments of food and supplies;
  2. Routinely inspecting the premises for evidence of pests;
  3. Using methods, if pests are found, such as trapping devices or other means of pest control as specified under subsections (6)(e), (6)(m), and (6)(n) of this Rule; Pf and
  4. Eliminating harborage conditions. Advised to deep cleaned and increase pest control.

16B - plumbing installed; proper backflow devices

Regulation: 511-6-1.06(2)(r) - system maintained in good repair (p, c)

2 ptsCorrected: NoRepeat: No

Observed leak at vegetable sink. Water continuous drip from basin. C/A: Corrective Action: 511-6-1.06(2)(r) - System Maintained in Good Repair (P, C) (r) System Maintained in Good Repair. A plumbing system shall be repaired according to law; P and maintained in good repair. Advised to have repaired.

Mar 11, 2025

Followup

Score: 942 violations

4-2B - food-contact surfaces: cleaned & sanitized

Regulation: 511-6-1.05(7)(b) - food contact surfaces and utensils - cleaning frequency (p, c)

4 ptsCorrected: YesRepeat: No

Observed the slicer unclean with encrusted food debris build up. Corrective Action: 511-6-1.05(7)(b) - Food Contact Surfaces and Utensils - Cleaning Frequency (P, C) (b) Equipment Food-Contact Surfaces and Utensils.

  1. Equipment food-contact surfaces and utensils shall be cleaned:

(i) Before each use with a different type of raw animal food such as beef, fish, lamb, pork, or poultry. It does not apply if the food-contact surface or utensil is in contact with a succession of different types of raw meat and raw poultry each requiring a higher cooking temperature as specified under DPH Rule 511-6-1.04(5)(a) than the previous type such as preparing raw pork followed by cutting raw poultry on the same cutting board; P

(ii) Each time there is a change from working with raw foods to working with ready-to-eat foods; P

(iii) Between uses with raw fruits and vegetables and with Time/Temperature Control for safety food; P

(iv) Before using or storing a food temperature measuring device; P and

(v) At any time during the operation when contamination may have occurred. P

Corrected onsite: slicer was moved to dish pit to be proper cleaned. Advised to increase cleaning frequency.

15C - nonfood-contact surfaces clean

Regulation: 511-6-1.05(7)(a)2,3 - equipment, food/nonfood-contact surfaces, and utensils, food-contact surfaces of cooking equipment & nonfood-contact surfaces free of accumulations (c)

1 ptsCorrected: NoRepeat: Yes

Observed inside of reach in cooler gaskets unclean to sight and touch. Food debris observed in between gaskets. Corrective Action: 511-6-1.05(7)(a)2,3 - Equipment, Food/Nonfood-Contact Surfaces, and Utensils, food-contact surfaces of cooking equipment & nonfood-contact surfaces free of accumulations (C) 2. The food-contact surfaces of cooking equipment and pans shall be kept free of encrusted grease deposits and other soil accumulations. 3. Nonfood-contact surfaces of equipment shall be kept free of an accumulation of dust, dirt, food residue, and other debris.

Advised to have deep cleaned and increase cleaning frequency.

Mar 10, 2025

Routine

Score: 4914 violations

4-1A - food separated and protected

Regulation: 511-6-1.04(4)(n)1 - gloves, use limitation (single use gloves) (p)

9 ptsCorrected: YesRepeat: No

Observed employee come from outside with gloved hands and rinse hands with gloves on and proceed to handle raw chicken. Corrective Action:511-6-1.04(4)(n)1 - Gloves, Use Limitation (single use gloves) (P) (n) Gloves, Use Limitation.

  1. If used, single-use gloves shall be used for only one task such as working with ready-to-eat food or with raw animal food, used for no other purpose, and discarded when damaged or soiled, or when interruptions occur in the operation. P Corrected onsite: Chicken was discarded and employee was educated on proper hand washing. Complied and washed hands before returning to work.

6-1A - proper cold holding temperatures

Regulation: 511-6-1.04(6)(f) - time/temperature control for safety; cold holding (p)

9 ptsCorrected: YesRepeat: Yes

Observed chicken(48F) and salmon mix(46F) stored in 2 door reach in cooler and Raw cut chicken (58F) stored on countertop not holding a TCS food temp of 41F or below. Corretive Action:511-6-1-.10 Compliance Procedures: (o) (1) Voluntary Closure. A food service establishment that is graded as a “U” and does not earn at least a grade “C” within ten (10) days of receiving the “U” will be requested to voluntarily close until all violations are corrected and/or have enforcement action taken to suspend or revoke the food service permit. Corrective Action: All foods items were discarded by PIC.

6-1C - proper cooling time and temperature

Regulation: 511-6-1.04(6)(d) - cooling (p)

9 ptsCorrected: YesRepeat: No

Observed TCS food items held in walk in cooler not cooling within 6 hours. smoked chicken (48F), cooked white rice(44F), black rice(47F) and yellow rice (46F) placed in walk in cooler to cool on 3/8/2025 with lids on tight. Corrective Action: 511-6-1.04(6)(d) - Cooling (P) (d) Cooling.

  1. Cooked time/temperature control for safety food shall be cooled:

(i) Within 2 hours from 135°F (57°C) to 70°F (21°C); P and

(ii) Within a total of 6 hours from 135°F (57°C) to 41°F (5°C) or less. P

  1. Time/temperature control for safety food shall be cooled within 4 hours to 41°F (5°C) or less if prepared from ingredients at ambient temperature, such as reconstituted foods and canned tuna. P

  2. Except as specified under paragraph 4 of this subsection, a time/temperature control for safety food received in compliance with laws allowing a temperature above 41°F (5°C) during shipment from the supplier shall be cooled within 4 hours to 41°F (5°C). P Corrected onsite: ALL TCS food items were discarded by PIC and DPH flyer was given to PIC

1-2B - certified food protection manager

Regulation: 511-6-1.03(3)(b) - certification requirements/exemptions (pf)

4 ptsCorrected: NoRepeat: No

No Certified Food Manager for establishment. Corrective Action: 511-6-1.03(3)(a) - Food Safety Manager Certification (Pf) Food service establishments shall have in its employ a Certified Food Safety Manager (CFSM) as specified in paragraph (b) of this subsection to ensure food safety is being managed within the food service establishment during all hours of operation as specified within paragraph (d) of this subsection. Pf Current CFSM has been gone for more than 30 days. Given establishment 60 days to obtain CFSM.

2-2D - adequate handwashing facilities supplied & accessible

Regulation: 511-6-1.07(3)(b) - hand drying provision (pf)

4 ptsCorrected: YesRepeat: Yes

Observed hand sink near 3 compartment sink without paper towels. Corrective Action:511-6-1.07(3)(b) - Hand Drying Provision (Pf) (b) Hand Drying Provision. Each handwashing sink or group of adjacent handwashing sinks shall be provided with:

  1. Individual, disposable towels; Pf

  2. A continuous towel system that supplies the user with a clean towel; Pf

  3. A heated-air hand drying device; Pf or

  4. A hand drying device that employs an air-knife system that delivers high velocity, pressurized air at ambient temperatures.Pf Corrected onsite paper towels were restocked and advised paper towels, soap and trash can shall be available at all hand sinks at all times.

2-2D - adequate handwashing facilities supplied & accessible

Regulation: 511-6-1.07(3)(a) - handwashing cleanser, availability (pf)

4 ptsCorrected: YesRepeat: Yes

Observed hand sinks in main kitchen without hand soap.
Corrective Action: (a) Handwashing Cleanser, Availability. Each handwashing sink or group of two adjacent handwashing sinks shall be provided with a supply of hand cleaning liquid, powder, or bar soap. Corrected on site: soap dispenser was restocked.

2-2D - adequate handwashing facilities supplied & accessible

Regulation: 511-6-1-.03(5)(d) - where to wash (pf)

4 ptsCorrected: YesRepeat: No

Observed employee washing hands at 3 compartment sink behind bar. Corrective Action: 511-6-1-.03(5)(d) - Where to wash (Pf) (d) Where to Wash. Food employees shall clean their hands in a handwashing sink or approved automatic handwashing facility and may not clean their hands in a sink used for food preparation or warewashing, or in a service sink or curbed cleaning facility used for the disposal of mop water and similar liquid waste. Pf Corrected onsite: Employee was educated on proper where to wash and complied by washing hands at hand sink behind bar.

4-2B - food-contact surfaces: cleaned & sanitized

Regulation: 511-6-1.05(6)(n) - manual and mechanical warewashing equipment, chemical sanitization-temperature, ph, concentration, hardness (p,pf)

4 ptsCorrected: YesRepeat: No

Observed employee washing dishes with no measurable amount of sanitizer. Corrective Action: 511-6-1.05(6)(n) - Manual and Mechanical Warewashing Equipment, Chemical Sanitization-Temperature, pH, Concentration, Hardness (P,Pf) (n) Manual and Mechanical Warewashing Equipment, Chemical Sanitization - Temperature, pH, Concentration, and Hardness. A chemical sanitizer used in a sanitizing solution for a manual or mechanical operation at contact times specified under subsection (8)(b)3 of this Rule shall meet the requirements specified in DPH Rule 511-6-1-.07(6)(g), shall be used in accordance with the Environmental Protection Agency (EPA)-registered label use instructions P, and shall be used as follows:

  1. A chlorine solution shall have a minimum temperature based on the concentration and pH of the solution as listed in the following chart; P

Concentration Range Minimum Temperature

MG/L PH 10 or less oF (oC) PH 8 or less oF (oC)

25-49 120 (49) 120 (49)

50-99 100 (38) 75 (24)

100 55 (13) 55 (13)

  1. A quaternary ammonium compound solution shall have a minimum temperature of 75ºF (24ºC), P have a concentration as specified in DPH Rule 511-6-1-.07(6)(g) and as indicated by the manufacturer’s use directions included in the labeling, P and be used only in water with 500 ppm hardness or less or in water having a hardness no greater than specified by the EPA-registered label use instructions; P

Corrected onsite: Employee was educated on the proper ware washing, complied and sink was remade to read 300 ppm Quats. Advised to use test strips when preparing sanitizer solutions.

6-2 - proper date marking and disposition

Regulation: 511-6-1.04(6)(g) - ready-to-eat time/temperature control for safety food, date marking (pf)

4 ptsCorrected: YesRepeat: Yes

Observed multiple cooked TCS food items and held for more than 24 hours without proper date markings. TCS foods were prepared 3/8/2025. Corrective Action: 511-6-1.04(6)(g) - Ready-To-Eat Time/Temperature Control for Safety Food, Date Marking (Pf) (g) Ready-to-Eat Time/Temperature Control for Safety Food, Date Marking

  1. Except when packaging food using a reduced oxygen packaging method, and except as specified in paragraphs 4 and 5 of this subsection, refrigerated, ready-to-eat, time/temperature control for safety food prepared and held in a food establishment for more than 24 hours shall be clearly marked to indicate the date or day by which the food shall be consumed on the premises, sold, or discarded, when held at a temperature of 41°F (5°C) or below for a maximum of 7 days. The day of preparation shall be counted as Day 1. Pf

  2. Except as specified in paragraphs 4 through 6 of this subsection, refrigerated, ready-to-eat, time/temperature control for safety food prepared and packaged by a food processing plant shall be clearly marked, at the time the original container is opened in a food service establishment and if the food is held for more than 24 hours, to indicate the date or day by which the food shall be consumed on the premises, sold, or discarded, when held at a temperature of 41°F (5°C) or below for a maximum of 7 days after the original container is opened. The day the original container is opened in the food service establishment shall be counted as Day 1, except, the day or date marked by the food service establishment may not exceed a manufacturer’s use by date if the manufacturer determined the use-by date based on food safety; Pf

  3. A refrigerated, ready-to-eat, time/temperature control for safety food ingredient or a portion of a refrigerated, ready-to-eat, time/temperature control for safety food that is subsequently combined with additional ingredients or portions of food shall retain the date marking of the earliest-prepared or first-prepared ingredient. Pf

  4. A date marking system that meets the criteria stated in paragraphs 1 and 2 of this subsection may include:

(i) Using a method approved by the Health Authority for refrigerated, ready-to-eat time / temperature control for safety food that is frequently rewrapped, such as lunchmeat or a roast, or for which date marking is impractical, such as soft serve mix or milk in a dispensing machine;

(ii) Marking the date or day of preparation, with a procedure to discard the food on or before the last date or day by which the food must be consumed on the premises, sold, or discarded;

(iii) Marking the date or day the original container is opened in a food service establishment, with a procedure to discard the food on or before the last date or day by which the food must be consumed on the premises, sold, or discarded; or

(iv) Using calendar dates, days of the week, color-coded marks, or other effective marking methods, provided that the marking system is disclosed to the Health Authority upon request.

  1. The requirements in paragraphs 1 and 2 of this subsection do not apply to individual meal portions served or repackaged for sale from a bulk container upon a consumer’s request.

  2. The requirement in paragraph 2 of this subsection does not apply to the following foods prepared and packaged by a food processing plant inspected by a Health Authority:

(ii) Hard cheeses containing not more than 39% moisture as defined in 21 CFR 133 Cheeses and related cheese products, such as cheddar, gruyere, parmesan and reggiano, and romano;

(iii) Semi-soft cheeses containing more than 39% moisture, but not more than 50% moisture, as defined in 21 CFR 133 Cheeses and related cheese products, such as blue, edam, gorgonzola, gouda, and monterey jack;

(iv) Cultured dairy products as defined in 21 CFR 131 Milk and cream, such as yogurt, sour cream, and buttermilk;

Corrected onsite: All ready to eat and TCS foods items stored for more than 24 hours were discarded. DPH JUST DATE IT Flyer was given to PIC

12B - personal cleanliness

Regulation: 511-6-1.03(5)(g) - jewelry (c)

3 ptsCorrected: YesRepeat: No

Observed employee preparing eggrolls and while wearing watch. Corrective Action: (g) Jewelry. Except for a plain ring such as a wedding band food employees may not wear jewelry including medical information jewelry on their arms and hands while preparing food. Corrected on site: watch was removed, raw chicken was discarded and hands were washed and sanitized before returning to work.

11A - proper cooling methods used: adequate equipment for temperature control

Regulation: 511-6-1.04(6)(e) - cooling methods (pf, c)

3 ptsCorrected: YesRepeat: No

3 pans of rice were observed in walk in cooler cooling with lids on tight. Smoked chicken in reach in cooler with lid on tight. Corrective Action:511-6-1.04(6)(e) - Cooling Methods (Pf, C) (e) Cooling Methods.

  1. Cooling shall be accomplished in accordance with the time and temperature criteria specified under DPH Rule 511-6-1-.04(6)(d) by using one or more of the following methods depending on the type of food being cooled:

(i) Placing the food in shallow pans; Pf

(ii) Separating the food into smaller or thinner portions; Pf

(iii) Using rapid cooling equipment; Pf

(iv) Stirring the food in a container placed in an ice water bath; Pf

(v) Using containers that facilitate heat transfer; Pf

(vi) Adding ice as an ingredient; Pf or

(vii) Other effective methods. Pf

  1. When placed in cooling or cold holding equipment, food containers in which food is being cooled shall be:

(i) Arranged in the equipment to provide maximum heat transfer through the container walls; and

(ii) Loosely covered, or uncovered if protected from overhead contamination during the cooling period to facilitate heat transfer from the surface of the food.

Corrected onsite: All items were discarded by PIC. DPH Flyer was given to PIC.

13A - posted: permit/inspection/choking poster/handwashing

Regulation: 511-6-1.02(1)(d) - displaying of the inspection report (c)

1 ptsCorrected: NoRepeat: No

Current inspection not posted Corrective Action: 511-6-1.02(1)(d) - Displaying of the Inspection Report (C)

  1. The most current inspection report shall be prominently displayed in public view at all times, within fifteen feet of the front or primary public door and between five feet and seven feet from the floor and in an area where it can be read at a distance of one foot away.

  2. Food service establishments with drive-thru windows will post the current inspection report, and also have the inspection report posted so that a minimum of the top one-third of a copy of the current inspection report is visible through each window allowing customers to easily read the score, date of inspection and establishment information.

  3. At food service establishments with no primary or public door, the current inspection report shall be prominently displayed at all times where the documents can be read by the public from a distance of one foot away. If requirements of this paragraph are not possible because of physical restrictions, a location will be determined as approved by the Health Authority.

  4. The most current inspection report for mobile food service units and extended food service units issued by the local Health Authority having jurisdiction for its inspections shall be prominently displayed in public view during all hours of operation. Such inspection reports shall be prominently displayed at the point of service where the documents can be read by the public from a distance of one foot away.

  5. A food service establishment inspection report addendum need not be displayed, but shall be made available by the food service establishment to the public upon request.

15C - nonfood-contact surfaces clean

Regulation: 511-6-1.05(7)(a)2,3 - equipment, food/nonfood-contact surfaces, and utensils, food-contact surfaces of cooking equipment & nonfood-contact surfaces free of accumulations (c)

1 ptsCorrected: NoRepeat: Yes

Observed inside of reach in coolers near grill unclean with heavy debris build up. Observed counter top under inside grill unclean with grease and food debris build up. Corrective Action: 511-6-1.05(7)(a)2,3 - Equipment, Food/Nonfood-Contact Surfaces, and Utensils, food-contact surfaces of cooking equipment & nonfood-contact surfaces free of accumulations (C) 2. The food-contact surfaces of cooking equipment and pans shall be kept free of encrusted grease deposits and other soil accumulations. 3. Nonfood-contact surfaces of equipment shall be kept free of an accumulation of dust, dirt, food residue, and other debris.

Advised to have deep cleaned and increase cleaning frequency.

17C - physical facilities installed, maintained, and clean

Regulation: 511-6-1.07(5)(a),(b) - good repair, physical facilities maintained; cleaning, frequency & restrictions, cleaned often enough to keep them clean (c)

1 ptsCorrected: NoRepeat: Yes

Floors behind equipment were observed with heavy debris build up. Corrective Action: 511-6-1.07(5)(a),(b) - Good Repair, physical facilities maintained; Cleaning, Frequency & Restrictions, cleaned often enough to keep them clean (C) (5) Maintenance and Operation.

(a) Good Repair. All physical facilities shall be maintained in good repair.

(b) Cleaning, Frequency and Restrictions.

  1. The physical facilities shall be cleaned as often as necessary to keep them clean and by methods that prevent contamination of food products. Advised to deep clean and increase cleaning frequency.

Oct 1, 2024

Followup

Score: 877 violations

4-2B - food-contact surfaces: cleaned & sanitized

Regulation: 511-6-1.05(7)(a)1 - equipment, food-contact surfaces,& utensils (pf)

4 ptsCorrected: YesRepeat: No

Observed utensils stored as clean with mold like substance and gnats in bottom of storage bin in direct contact with utensils.
Corrective Action: 511-6-1.05(7)(a)1 - Equipment, Food-Contact Surfaces,& Utensils (Pf) (7) Cleaning of Equipment and Utensils.

(a) Equipment, Food-Contact Surfaces, and Utensils.

  1. Equipment food-contact surfaces and utensils shall be clean to sight and touch. Pf. Corrected onsite: all utensils were moved to dish pit to be washed. Advised to increase cleaning frequency.

11A - proper cooling methods used: adequate equipment for temperature control

Regulation: 511-6-1.04(6)(e) - cooling methods (pf, c)

3 ptsCorrected: YesRepeat: No

3 pans of rice were observed in walk in cooler cooling with lids on tight. Corrective Action:511-6-1.04(6)(e) - Cooling Methods (Pf, C) (e) Cooling Methods.

  1. Cooling shall be accomplished in accordance with the time and temperature criteria specified under DPH Rule 511-6-1-.04(6)(d) by using one or more of the following methods depending on the type of food being cooled:

(i) Placing the food in shallow pans; Pf

(ii) Separating the food into smaller or thinner portions; Pf

(iii) Using rapid cooling equipment; Pf

(iv) Stirring the food in a container placed in an ice water bath; Pf

(v) Using containers that facilitate heat transfer; Pf

(vi) Adding ice as an ingredient; Pf or

(vii) Other effective methods. Pf

  1. When placed in cooling or cold holding equipment, food containers in which food is being cooled shall be:

(i) Arranged in the equipment to provide maximum heat transfer through the container walls; and

(ii) Loosely covered, or uncovered if protected from overhead contamination during the cooling period to facilitate heat transfer from the surface of the food.

Corrected onsite: pans were removed from walk in cooler placed on ice to complete proper cooling process. DPH Flyer was given to PIC.

18 - insects, rodents, and animals not present

Regulation: 511-6-1.07(5)(k) - controlling pests (pf, c)

3 ptsCorrected: NoRepeat: No

Observed gnats and flies in main kitchen. Corrective Action: 511-6-1.07(5)(k) - Controlling Pests (Pf, C) (k) Controlling Pests. The presence of insects, rodents, and other pests shall be controlled to minimize their presence on the premises by:

  1. Routinely inspecting incoming shipments of food and supplies;
  2. Routinely inspecting the premises for evidence of pests;
  3. Using methods, if pests are found, such as trapping devices or other means of pest control as specified under subsections (6)(e), (6)(m), and (6)(n) of this Rule; Pf and
  4. Eliminating harborage conditions. Advised to deep cleaned

15A - food and nonfood-contact surfaces cleanable, properly designed, constructed, and used

Regulation: 511-6-1.05(6)(b) - cutting surfaces (c)

1 ptsCorrected: NoRepeat: No

Observed cutting board in main kitchen unclean to sight with deep grooves which does not allow proper cleaning. Corrective Action: Observed cutting board in main kitchen unclean to sight with deep grooves which does not allow proper cleaning. Advised to have deep cleaned or replaced.

17C - physical facilities installed, maintained, and clean

Regulation: 511-6-1.07(5)(a),(b) - good repair, physical facilities maintained; cleaning, frequency & restrictions, cleaned often enough to keep them clean (c)

1 ptsCorrected: NoRepeat: Yes

Floors behind equipment were observed with heavy debris build up. Corrective Action: 511-6-1.07(5)(a),(b) - Good Repair, physical facilities maintained; Cleaning, Frequency & Restrictions, cleaned often enough to keep them clean (C) (5) Maintenance and Operation.

(a) Good Repair. All physical facilities shall be maintained in good repair.

(b) Cleaning, Frequency and Restrictions.

  1. The physical facilities shall be cleaned as often as necessary to keep them clean and by methods that prevent contamination of food products.

  2. Except for cleaning that is necessary due to a spill or other accident, cleaning shall be done during periods when the least amount of food is exposed, such as after closing. Advised to have deep cleaned.

17D - adequate ventilation and lighting; designated areas used

Regulation: 511-6-1.07(3)(f) - lighting intensity, adequate in food prep, storage & service areas (c)

1 ptsCorrected: NoRepeat: Yes

Observed light out in walk in freezer Corrective Action: 511-6-1.07(3)(f) - Lighting Intensity, adequate in food prep, storage & service areas (C) (f) Lighting Intensity. The light intensity shall be:

  1. At least 10 foot candles (108 lux) at a distance of 30 inches (75 cm) above the floor, in walk-in refrigeration units and dry food storage areas and in other areas and rooms during periods of cleaning;

  2. At least 20 foot candles (215 lux):

(i) At a surface where food is provided for consumer self-service such as buffets and salad bars or where fresh produce or packaged foods are sold or offered for consumption;

(ii) Inside equipment such as reach-in and under-counter refrigerators;

(iii) At a distance of 30 inches (75 cm) above the floor in areas used for handwashing, warewashing, and equipment and utensil storage, and in toilet rooms; and

  1. At least 50 foot candles (540 lux) at a surface where a food service employee is working with food or working with utensils or equipment such as knives, slicers, grinders, or saws where employee safety is a factor.

Advised to have replaced.

17D - adequate ventilation and lighting; designated areas used

Regulation: 511-6-1.07(4)(b) - designated areas for employee activity, located to prevent contamination of food, equipment, utensils, linens, & single service articles (c)

1 ptsCorrected: YesRepeat: No

Multiple personal bottles were stored on throughout main kitchen. Corrective Action:511-6-1.07(4)(b) - Designated Areas for Employee Activity, located to prevent contamination of food, equipment, utensils, linens, & single service articles (C) (b) Designated Areas for Employee Activity.

  1. Areas designated for employees to eat, drink, and use tobacco shall be located so that food, equipment, linens, and single-service and single-use articles are protected from contamination.

  2. Lockers or other suitable facilities shall be located in a designated room or area where contamination of food, equipment, utensils, linens and single-service and single-use articles cannot occur.

Corrected onsite: all bottles were discarded.

Sep 17, 2024

Routine

Score: 6216 violations

2-1B - hands clean and properly washed

Regulation: 511-6-1.03(5)(c) - when to wash (p)

9 ptsCorrected: YesRepeat: No

Observed employee place on hair net and proceed to place on gloves without washing hands. Corrective Action: 511-6-1.03(5)(c) - When to Wash (P) (c) When to Wash.

  1. Food employees shall clean their hands and exposed portions of their arms immediately before engaging in food preparation including working with exposed food, clean equipment and utensils, and unwrapped single-service and single-use articles P and:

(i) After touching bare human body parts other than clean hands and clean, exposed arms; P

(ii) After using the toilet room; P

(iii) After caring for or handling service animals or aquatic animals; P

(iv) After coughing, sneezing, using a handkerchief or disposable tissue, using tobacco, eating, or drinking, except for drinking from a closed beverage container and the container is handled to prevent contamination of the hands; P

(v) After handling soiled equipment or utensils; P

(vi) During food preparation, as often as necessary to remove soil and contamination and to prevent cross contamination when changing tasks; P

(vii) When switching between working with raw food and working with ready-to-eat food; P

(viii) Before donning gloves to initiate a task that involves working with food; P and

(ix) After engaging in other activities that contaminate the hands. P

  1. All employees shall wash hands before leaving the restroom. All food employees leaving the restroom shall wash their hands again upon re-entering the food preparation area. Corrected onsite: employee removed gloves washed hands before returning to work.

2-2A - management knowledge, responsibilities, reporting

Regulation: 511-6-1.03(1)(c)2,3 - demonstration (pf)

4 ptsCorrected: YesRepeat: No

Employee health policy & written agreement unable to be provided to verify that employees have been made aware of their reporting responsibilities with diseases transmissible through food. Corrective Action: 511-6-1.03(1)(c)2,3 - Demonstration (Pf) 2. Explaining the responsibility of the person in charge for preventing the transmission of foodborne disease by a food employee who has a disease or medical condition that may cause foodborne disease; Pf

  1. Describing the symptoms associated with the diseases that are transmissible through food; Pf

Corrected onsite: Inspector provided Employee health agreement for current employees to sign.

2-2D - adequate handwashing facilities supplied & accessible

Regulation: 511-6-1.07(3)(a) - handwashing cleanser, availability (pf)

4 ptsCorrected: YesRepeat: Yes

Observed hand sinks in main kitchen without hand soap.
Corrective Action: (a) Handwashing Cleanser, Availability. Each handwashing sink or group of two adjacent handwashing sinks shall be provided with a supply of hand cleaning liquid, powder, or bar soap. Corrected on site: soap dispenser was restocked.

2-2D - adequate handwashing facilities supplied & accessible

Regulation: 511-6-1.07(3)(b) - hand drying provision (pf)

4 ptsCorrected: YesRepeat: No

Observed both sinks in main kitchen without paper towels. Corrective Action: 511-6-1.07(3)(b) - Hand Drying Provision (Pf) (b) Hand Drying Provision. Each handwashing sink or group of adjacent handwashing sinks shall be provided with:

  1. Individual, disposable towels; Pf

  2. A continuous towel system that supplies the user with a clean towel; Pf

  3. A heated-air hand drying device; Pf or

Corrected onsite: Paper towels were restocked and advised that hand sinks shall have paper towels at all times.

2-2D - adequate handwashing facilities supplied & accessible

Regulation: 511-6-1.06(2)(o) - using a handwashing sink- operation & maintenance (pf)

4 ptsCorrected: YesRepeat: No

Observed bottles of liquor stored in hand sink behind bar. Observed strainer and spoon stored in hand sink in main kitchen near 3 compartment sink. Corrective Action: 511-6-1.06(2)(o) - Using a Handwashing Sink- Operation & maintenance (Pf) (o) Using a Handwashing Sink.

  1. A handwashing sink shall be maintained so that it is accessible at all times for employee use. Pf

  2. A handwashing facility may not be used for purposes other than handwashing. Pf

  3. An automatic handwashing facility shall be used in accordance with manufacturer’s instructions. Pf Corrected onsite: Items were removed from hand sinks by PIC and advised handsinks shall remain clear at all times.

2-2D - adequate handwashing facilities supplied & accessible

Regulation: 511-6-1-.03(5)(d) - where to wash (pf)

4 ptsCorrected: YesRepeat: No

Observed employee wash hands at mop sink. Corrective Action: 511-6-1-.03(5)(d) - Where to wash (Pf) (d) Where to Wash. Food employees shall clean their hands in a handwashing sink or approved automatic handwashing facility and may not clean their hands in a sink used for food preparation or warewashing, or in a service sink or curbed cleaning facility used for the disposal of mop water and similar liquid waste. Pf Corrected onsite: Employee was educated on proper handwashing by inspector and advised to wash hands at hand sink.

2-2E - response procedures for vomiting & diarrheal events

Regulation: 511-6-1.03(6) - clean-up of vomiting and diarrheal events(pf)

4 ptsCorrected: YesRepeat: Yes

The Person in Charge could not provide details or proof during the inspection that a proper disinfectant would be utilized for responding to a vomiting or diarrheal event in the the establishment. Corrective action: (6) Responding To Contamination Events. A food establishment shall have procedures for employees to follow when responding to vomiting or diarrheal events that involve the discharge of vomitus or fecal matter onto surfaces in the food service establishment. The procedures shall address the specific actions employees must take to minimize the spread of contamination and the exposure of employees, consumers, food, and surfaces to vomitus or fecal matter. Corrected on site: PIC purchased EPA approved chemical while inspector was on site.

6-2 - proper date marking and disposition

Regulation: 511-6-1.04(6)(g) - ready-to-eat time/temperature control for safety food, date marking (pf)

4 ptsCorrected: YesRepeat: No

Observed serval items cooked and held for more than 24 hours without proper labeling. Corrective Action: 511-6-1.04(6)(g) - Ready-To-Eat Time/Temperature Control for Safety Food, Date Marking (Pf) (g) Ready-to-Eat Time/Temperature Control for Safety Food, Date Marking

  1. Except when packaging food using a reduced oxygen packaging method, and except as specified in paragraphs 4 and 5 of this subsection, refrigerated, ready-to-eat, time/temperature control for safety food prepared and held in a food establishment for more than 24 hours shall be clearly marked to indicate the date or day by which the food shall be consumed on the premises, sold, or discarded, when held at a temperature of 41°F (5°C) or below for a maximum of 7 days. The day of preparation shall be counted as Day 1. Pf

  2. Except as specified in paragraphs 4 through 6 of this subsection, refrigerated, ready-to-eat, time/temperature control for safety food prepared and packaged by a food processing plant shall be clearly marked, at the time the original container is opened in a food service establishment and if the food is held for more than 24 hours, to indicate the date or day by which the food shall be consumed on the premises, sold, or discarded, when held at a temperature of 41°F (5°C) or below for a maximum of 7 days after the original container is opened. The day the original container is opened in the food service establishment shall be counted as Day 1, except, the day or date marked by the food service establishment may not exceed a manufacturer’s use by date if the manufacturer determined the use-by date based on food safety; Pf

  3. A refrigerated, ready-to-eat, time/temperature control for safety food ingredient or a portion of a refrigerated, ready-to-eat, time/temperature control for safety food that is subsequently combined with additional ingredients or portions of food shall retain the date marking of the earliest-prepared or first-prepared ingredient. Pf

  4. A date marking system that meets the criteria stated in paragraphs 1 and 2 of this subsection may include:

(i) Using a method approved by the Health Authority for refrigerated, ready-to-eat time / temperature control for safety food that is frequently rewrapped, such as lunchmeat or a roast, or for which date marking is impractical, such as soft serve mix or milk in a dispensing machine;

(ii) Marking the date or day of preparation, with a procedure to discard the food on or before the last date or day by which the food must be consumed on the premises, sold, or discarded;

(iii) Marking the date or day the original container is opened in a food service establishment, with a procedure to discard the food on or before the last date or day by which the food must be consumed on the premises, sold, or discarded; or

(iv) Using calendar dates, days of the week, color-coded marks, or other effective marking methods, provided that the marking system is disclosed to the Health Authority upon request.

  1. The requirements in paragraphs 1 and 2 of this subsection do not apply to individual meal portions served or repackaged for sale from a bulk container upon a consumer’s request.

  2. The requirements in paragraphs 1 and 2 of this subsection do not apply to shellstock.

  3. The requirement in paragraph 2 of this subsection does not apply to the following foods prepared and packaged by a food processing plant inspected by a Health Authority:

(i) Deli salads, such as ham salad, seafood salad, chicken salad, egg salad, pasta salad, potato salad, and macaroni salad, manufactured in accordance with 21 CFR 110 Current good manufacturing practice in manufacturing, packing, or holding human food;

(ii) Hard cheeses containing not more than 39% moisture as defined in 21 CFR 133 Cheeses and related cheese products, such as cheddar, gruyere, parmesan and reggiano, and romano;

(iii) Semi-soft cheeses containing more than 39% moisture, but not more than 50% moisture, as defined in 21 CFR 133 Cheeses and related cheese products, such as blue, edam, gorgonzola, gouda, and monterey jack;

(iv) Cultured dairy products as defined in 21 CFR 131 Milk and cream, such as yogurt, sour cream, and buttermilk;

(v) Preserved fish products, such as pickled herring and dried or salted cod, and other acidified fish products defined in 21 CFR 114 Acidified foods;

(vi) Shelf stable, dry fermented sausages, such as pepperoni and Genoa salami; and

(vii) Shelf stable salt-cured products, such as prosciutto and Parma ham. Corrected onsite: All items stored for more than 24 hours were labeled.

8-2B - toxic substances properly identified, stored, used

Regulation: 511-6-1.07(6)(g) - chemical sanitizers, criteria (p)

4 ptsCorrected: YesRepeat: No

Observed dish machine behind bar reading 200+ ppm Cl. Corrective Action: 511-6-1.07(6)(g) - Chemical Sanitizers, Criteria (P) (g) Chemical Sanitizers, Criteria. Chemical sanitizers, including chemical sanitizing solutions generated on-site, and other chemical antimicrobials applied to food-contact surfaces shall:

  1. Meet requirements specified in 40 CFR 180.940 Tolerance exemptions for active and inert ingredients for use in antimicrobial formulations (Food-contact surface sanitizing solutions) P, or

  2. Meet the requirements as specified in 40 CFR 180.2020 Pesticide Chemicals Not Requiring a Tolerance or Exemption from Tolerance-Non-food determinations. P Corrected onsite: Dish machine was serviced and reads 100ppm Cl

18 - insects, rodents, and animals not present

Regulation: 511-6-1.07(2)(m) - outer openings protected (c)

3 ptsCorrected: YesRepeat: No

Observed fly fan at rear door of main kitchen not working while is propped open. Corrective Action: 511-6-1.07(2)(m) - Outer Openings Protected (C) (m) Outer Openings, Protected.

  1. Except as specified in paragraphs 2 through 5 of this subsection, outer openings of a food service establishment shall be protected against the entry of insects and rodents by:

(i) Filling or closing holes and other gaps along floors, walls, and ceilings;

(ii) Closed, tight-fitting windows; and

(iii) Solid, self-closing, tight-fitting doors.

  1. The requirements in paragraph 1 of this subsection does not apply if a food service establishment opens into a larger structure, such as a mall, airport, or office building, or into an attached structure, such as a porch, and the outer openings from the larger or attached structure are protected against the entry of insects and rodents.

  2. Exterior doors used as exits need not be self-closing if they are:

(i) Solid and tight-fitting;

(ii) Designated for use only when an emergency exists, by the fire protection authority that has jurisdiction over the food establishment; and

(iii) Limited-use so they are not used for entrance or exit from the building for purposes other than the designated emergency exit use.

  1. Except as specified in paragraphs 2 and 5 of this subsection, if the windows or doors of a food service establishment, or of a larger structure within which a food service establishment is located, are kept open for ventilation or other purposes or a temporary food service establishment is not provided with windows and doors as specified under paragraph 1 of this subsection, the openings shall be protected against the entry of insects and rodents by:

(i) 16 mesh to 1 inch (16 mesh to 25.4 mm) screens;

(ii) Properly designed and installed air curtains to control flying insects; or

(iii) Other effective means.

  1. The requirement in paragraph 4 of this subsection does not apply if flying insects and other pests are absent due to the location of the establishment, the weather, or other limiting condition.

Corrected onsite: door was closed and advised not to prop door open without the fly fan working properly.

12A - contamination prevented during food preparation, storage, display

Regulation: 511-6-1.04(4)(q) - food storage (c)

3 ptsCorrected: YesRepeat: Yes

Observed sauces stored on floor near hand sink and dish machine. Corrective Action: 511-6-1.04(4)(q) - Food Storage (C) (q) Food Storage.

  1. Except as specified in paragraphs 2 and 3 of this subsection, food shall be protected from contamination by storing the food:

(i) In a clean, dry location;

(ii) Where it is not exposed to splash, dust, or other contamination; and

(iii) At least 6 inches (15 cm) above the floor.

  1. Food in packages and working containers may be stored less than 6 inches (15 cm) above the floor on case lot handling equipment if the equipment can be moved by hand or by conveniently available apparatuses such as hand trucks and forklifts.

  2. Pressurized beverage containers, cased food in waterproof containers such as bottles or cans, and milk containers in plastic crates may be stored on a floor that is clean and not exposed to floor moisture. Corrected onsite: Sauces were moved to the shelf below prep top 6 inches off the floor.

16B - plumbing installed; proper backflow devices

Regulation: 511-6-1.06(2)(r) - system maintained in good repair (p, c)

2 ptsCorrected: NoRepeat: Yes

Observed sink faucet at 3 compartment sink not working. Water does not turn off. Observed 3 compartment sink behind bar has leak at faucet. Water has continuous drip. Corrective Action: 511-6-1.06(2)(r) - System Maintained in Good Repair (P, C) (r) System Maintained in Good Repair. A plumbing system shall be repaired according to law; P and maintained in good repair. Advised to have repaired.

13A - posted: permit/inspection/choking poster/handwashing

Regulation: 511-6-1.02(1)(f)(1) - permit, displayed (c)

1 ptsCorrected: NoRepeat: No

Current permit has not been paid. Please contact404-508-7900 to pay current permit fees. Corrective Action: 511-6-1.02(1)(f)(1) - Permit, Displayed (C)

  1. Post the permit in a location in the food service establishment that is conspicuous to consumers

15C - nonfood-contact surfaces clean

Regulation: 511-6-1.05(7)(a)2,3 - equipment, food/nonfood-contact surfaces, and utensils, food-contact surfaces of cooking equipment & nonfood-contact surfaces free of accumulations (c)

1 ptsCorrected: NoRepeat: Yes

Observed all shelf inside the walk in cooler unclean with food debris and rust build up. Observed inside of oven unclean with heavy debris build up. Observed inside of reach in coolers near grill unclean with heavy debris build up. Observed inside of drawer under grill unclean with grease and food debris build up. Corrective Action: 511-6-1.05(7)(a)2,3 - Equipment, Food/Nonfood-Contact Surfaces, and Utensils, food-contact surfaces of cooking equipment & nonfood-contact surfaces free of accumulations (C) 2. The food-contact surfaces of cooking equipment and pans shall be kept free of encrusted grease deposits and other soil accumulations.

  1. Nonfood-contact surfaces of equipment shall be kept free of an accumulation of dust, dirt, food residue, and other debris.

Advised to have deep cleaned.

17C - physical facilities installed, maintained, and clean

Regulation: 511-6-1.07(5)(a),(b) - good repair, physical facilities maintained; cleaning, frequency & restrictions, cleaned often enough to keep them clean (c)

1 ptsCorrected: NoRepeat: Yes

Observed missing ceiling tiles. Observed walls behind bar unclean with debris build up. Observed floor in walk in freezer unclean with debris build up. Corrective Action: 511-6-1.07(5)(a),(b) - Good Repair, physical facilities maintained; Cleaning, Frequency & Restrictions, cleaned often enough to keep them clean (C) (5) Maintenance and Operation.

(a) Good Repair. All physical facilities shall be maintained in good repair.

(b) Cleaning, Frequency and Restrictions.

  1. The physical facilities shall be cleaned as often as necessary to keep them clean and by methods that prevent contamination of food products.

  2. Except for cleaning that is necessary due to a spill or other accident, cleaning shall be done during periods when the least amount of food is exposed, such as after closing.

Advised to have deep cleaned and increase cleaning frequency.

17D - adequate ventilation and lighting; designated areas used

Regulation: 511-6-1.07(3)(f) - lighting intensity, adequate in food prep, storage & service areas (c)

1 ptsCorrected: NoRepeat: No

Observed light out in walk in freezer Corrective Action: 511-6-1.07(3)(f) - Lighting Intensity, adequate in food prep, storage & service areas (C) (f) Lighting Intensity. The light intensity shall be:

  1. At least 10 foot candles (108 lux) at a distance of 30 inches (75 cm) above the floor, in walk-in refrigeration units and dry food storage areas and in other areas and rooms during periods of cleaning;

  2. At least 20 foot candles (215 lux):

(i) At a surface where food is provided for consumer self-service such as buffets and salad bars or where fresh produce or packaged foods are sold or offered for consumption;

(ii) Inside equipment such as reach-in and under-counter refrigerators;

(iii) At a distance of 30 inches (75 cm) above the floor in areas used for handwashing, warewashing, and equipment and utensil storage, and in toilet rooms; and

  1. At least 50 foot candles (540 lux) at a surface where a food service employee is working with food or working with utensils or equipment such as knives, slicers, grinders, or saws where employee safety is a factor.

Advised to have replaced.

May 30, 2024

Followup

Score: 933 violations

11C - approved thawing methods used

Regulation: 511-6-1.04(6)(c) - thawing (c)

3 ptsCorrected: YesRepeat: Yes

Observed raw chicken at meat sink sitting in standing water. Corrective action: Under refrigeration that maintains the food temperature at 41°F (5°C) or less or 2.Completely submerged under running water: (i) At a water temperature of 70°F (21°C) or below. COS- water was turned on to complete thawing process.

13A - posted: permit/inspection/choking poster/handwashing

Regulation: 511-6-1.02(1)(d) - displaying of the inspection report (c)

1 ptsCorrected: NoRepeat: No

Current inspection not posted.

17D - adequate ventilation and lighting; designated areas used

Regulation: 511-6-1.07(4)(b) - designated areas for employee activity, located to prevent contamination of food, equipment, utensils, linens, & single service articles (c)

1 ptsCorrected: YesRepeat: Yes

Observed several personal items stored through out the main kitchen. Cell phones stored on prep top counter, back pack stored on rolling rack. Areas designated for employees to eat, drink, and use tobacco shall be located so that food, equipment, linens, and single-service and single-use articles are protected from contamination. 2. Lockers or other suitable facilities shall be located in a designated room or area where contamination of food, equipment, utensils, linens and single-service and single-use articles cannot occur. COS- all items were moved to personal storage area.

May 15, 2024

Routine

Score: 7519 violations

2-2B - proper eating, tasting, drinking, or tobacco use

Regulation: 511-6-1.03(5)(k)1&2 - eating, drinking, or using tobacco (c)

4 ptsCorrected: YesRepeat: No

Observed employee drink without lid stored on prep top counter near dish machine. Corrective Action: 2. Employees shall consume food only in approved designated areas separate from food preparation and serving areas, equipment or utensil areas and food storage areas. However, drinking from a single service beverage cup with a secure lid and straw that is handled to prevent contamination of the employee’s hands, the container, exposed food, clean equipment, utensils and linens, unwrapped single-service and single-use articles will be allowed. Corrected on site: cup was discarded by employee.

2-2D - adequate handwashing facilities supplied & accessible

Regulation: 511-6-1.07(3)(a) - handwashing cleanser, availability (pf)

4 ptsCorrected: YesRepeat: No

Observed hand sink near dish machine without hand soap. Corrective Action: (a) Handwashing Cleanser, Availability. Each handwashing sink or group of two adjacent handwashing sinks shall be provided with a supply of hand cleaning liquid, powder, or bar soap. Corrected on site: soap dispenser was restocked.

2-2E - response procedures for vomiting & diarrheal events

Regulation: 511-6-1.03(6) - clean-up of vomiting and diarrheal events(pf)

4 ptsCorrected: NoRepeat: No

The Person in Charge could not provide details or proof during the inspection that a proper disinfectant would be utilized for responding to a vomiting or diarrheal event in the the establishment. Corrective action: (6) Responding To Contamination Events. A food establishment shall have procedures for employees to follow when responding to vomiting or diarrheal events that involve the discharge of vomitus or fecal matter onto surfaces in the food service establishment. The procedures shall address the specific actions employees must take to minimize the spread of contamination and the exposure of employees, consumers, food, and surfaces to vomitus or fecal matter. Corrected on site: PIC purchased EPA approved chemical while inspector was on site.

4-2B - food-contact surfaces: cleaned & sanitized

Regulation: 511-6-1.05(7)(b) - food contact surfaces and utensils - cleaning frequency (p, c)

4 ptsCorrected: NoRepeat: No

Observed cutting board in main kitchen unclean to sight with deep grooves which does not allow proper cleaning. Corrective Action: (II) Absent manufacturer specifications, at a frequency necessary to preclude accumulation of soil or mold. Advised to have deep cleaned.

4-2B - food-contact surfaces: cleaned & sanitized

Regulation: 511-6-1.05(7)(c) - cooking & baking equipment (c)

4 ptsCorrected: YesRepeat: No

Observed rice crocks unclean to sight and touch. Corrective Action: c) Cooking and Baking Equipment.

  1. The food-contact surfaces of cooking and baking equipment shall be cleaned at least every 24 hours. This subsection does not apply to hot oil cooking and filtering equipment if it is cleaned as specified under subsection (7)(b)3(v) of this Rule Rice was discarded and crocks were cleaned and sanitized. Advised to increase cleaning frequency.

4-2B - food-contact surfaces: cleaned & sanitized

Regulation: 511-6-1.05(7)(a)1 - equipment, food-contact surfaces,& utensils (pf)

4 ptsCorrected: YesRepeat: No

Observed raw meat thawing in vegetable sink. Corrective Action: (7) Cleaning of Equipment and Utensils. (a) Equipment, Food-Contact Surfaces, and Utensils.

  1. Equipment food-contact surfaces and utensils shall be clean to sight and touch. Corrected on site: raw meat was moved to walk in cooler.

8-2B - toxic substances properly identified, stored, used

Regulation: 511-6-1.07(6)(d) - restriction (pf)

4 ptsCorrected: YesRepeat: No

Observed Raid stored behind bar. Corrective Action:(d) Restriction.

  1. Only those poisonous or toxic materials that are required for the operation and maintenance of the food service establishment, such as for the cleaning and sanitizing of equipment and utensils, and the control of insects and rodents shall be allowed in a food service establishment. Corrected on site: raid was discarded

12B - personal cleanliness

Regulation: 511-6-1.03(5)(j) - hair restraints (c)

3 ptsCorrected: YesRepeat: No

Observed employee with hair long than 1/2 inch with no hair restraint. Corrective Action: (i) Hair Restraints:

  1. Employees preparing or handling food shall use effective and clean, disposable or easily cleanable nets or other hair restraints approved by the Health Authority, worn properly to restrain loose hair including beards and mustaches longer than one half inch. Corrected on site: hair restraint was added to head.

18 - insects, rodents, and animals not present

Regulation: 511-6-1.07(5)(k) - controlling pests (pf, c)

3 ptsCorrected: NoRepeat: No

Observed several flies in main dining area near front window. (k) Controlling Pests. The presence of insects, rodents, and other pests shall be controlled to minimize their presence on the premises by:

  1. Routinely inspecting incoming shipments of food and supplies;
  2. Routinely inspecting the premises for evidence of pests;
  3. Using methods, if pests are found, such as trapping devices or other means of pest control as specified under subsections (6)(e), (6)(m), and (6)(n) of this Rule and
  4. Eliminating harborage conditions.

Advised to increase pest control.

11C - approved thawing methods used

Regulation: 511-6-1.04(6)(c) - thawing (c)

3 ptsCorrected: YesRepeat: No

Observed raw chicken in meat sink sitting in standing water. Observed raw fish sitting on counter top in standing water. Observed raw pork stored in vegetable sink in standing water. Corrective Action: (c) Thawing. Except as specified in paragraph 4 of this subsection, time/temperature control for safety food shall be thawed:

  1. Under refrigeration that maintains the food temperature at 41°F (5°C) or less; or
  2. Completely submerged under running water: (i) At a water temperature of 70°F (21°C) or below, (ii) With sufficient water velocity to agitate and float off loose particles in an overflow, and (iii) For a period of time that does not allow thawed portions of ready-to-eat food to rise above 41°F (5°C), or (iv) For a period of time that does not allow thawed portions of a raw animal food requiring cooking to be above 41°F (5°C), for more than 4 hours including: (I) The time the food is exposed to the running water and the time needed for preparation for cooking, or (II) The time it takes under refrigeration to lower the food temperature to 41°F (5°C); Corrected on site: Raw pork was moved to walk in cooler, raw chicken was placed under running water and raw fish was moved to walk in cooler to complete proper thawing method. Flyer was given to PIC.

12A - contamination prevented during food preparation, storage, display

Regulation: 511-6-1.04(4)(q) - food storage (c)

3 ptsCorrected: YesRepeat: No

Observed 6 cases of raw chicken stored on walk in cooler floor under racks. Corrective Action: (q) Food Storage. 1. Except as specified in paragraphs 2 and 3 of this subsection, food shall be protected from contamination by storing the food: (iii) At least 6 inches (15 cm) above the floor. Corrected on site: cases of chicken were moved to racks in walk in cooler.

12B - personal cleanliness

Regulation: 511-6-1.03(5)(g) - jewelry (c)

3 ptsCorrected: YesRepeat: No

Observed employee preparing raw chicken while wearing watch. Corrective Action: (g) Jewelry. Except for a plain ring such as a wedding band food employees may not wear jewelry including medical information jewelry on their arms and hands while preparing food. Corrected on site: watch was removed, raw chicken was discarded and hands were washed and sanitized before returning to work.

16B - plumbing installed; proper backflow devices

Regulation: 511-6-1.06(2)(r) - system maintained in good repair (p, c)

2 ptsCorrected: NoRepeat: No

Observed sink faucets at 3 compartment sink behind bar with continuous leak. Corrective Action: (r) System Maintained in Good Repair. A plumbing system shall be repaired according to law; P and maintained in good repair. Advised to have repaired.

15A - food and nonfood-contact surfaces cleanable, properly designed, constructed, and used

Regulation: 511-6-1.05(1)(a) - materials, general requirements (p, c)

1 ptsCorrected: NoRepeat: No

Observed shelf in outside cooking area and main kitchen lined with foil. (a) General Requirements. Utensils and food-contact surfaces of equipment shall be made of materials that do not allow the migration of deleterious substances or impart colors, odors, or tastes to food and under normal use conditions, and shall be: P safe P, durable, corrosion-resistant, and nonabsorbent. In addition, materials shall be sufficient in weight and thickness to withstand repeated warewashing and shall be finished to have a smooth, easily cleanable surface. Materials shall be resistant to pitting, chipping, crazing, scratching, scoring, distortion and decomposition. Advised to have foil removed from shelves.

15C - nonfood-contact surfaces clean

Regulation: 511-6-1.05(7)(d) - nonfood-contact surfaces (c)

1 ptsCorrected: NoRepeat: No

Observed outside of ALL cooking equipment unclean to sight and touch with heavy debris build up. Corrective Action:(d) Nonfood-Contact Surfaces. Nonfood-contact surfaces of equipment shall be cleaned at a frequency necessary to preclude accumulation of soil residues. Advised to have deep cleaned.

17C - physical facilities installed, maintained, and clean

Regulation: 511-6-1.07(5)(a),(b) - good repair, physical facilities maintained; cleaning, frequency & restrictions, cleaned often enough to keep them clean (c)

1 ptsCorrected: NoRepeat: No

Observed floors, walls, ceiling and coving unclean to site and touch in main kitchen and behind bar. Corrective Action: (5) Maintenance and Operation. (a) Good Repair. All physical facilities shall be maintained in good repair. (b) Cleaning, Frequency and Restrictions.

  1. The physical facilities shall be cleaned as often as necessary to keep them clean and by methods that prevent contamination of food products.
  2. Except for cleaning that is necessary due to a spill or other accident, cleaning shall be done during periods when the least amount of food is exposed, such as after closing. Advised to have deep cleaned.

17C - physical facilities installed, maintained, and clean

Regulation: 511-6-1.07(5)(n) - maintaining premises, free of unnecessary items/litter (c)

1 ptsCorrected: NoRepeat: No

Observed outside back door unclean with unused equipment, shopping carts and other debris build up. Corrective Action: (n) Maintaining Premises. The premises shall be free of items that are unnecessary to the operation or maintenance of the establishment, such as litter or equipment that is nonfunctional or no longer used and litter. Advised to removed all unused equipment and trash.

17C - physical facilities installed, maintained, and clean

Regulation: 511-6-1.07(5)(a),(b) - good repair, physical facilities maintained; cleaning, frequency & restrictions, cleaned often enough to keep them clean (c)

1 ptsCorrected: NoRepeat: No

Observed floor in walk in freezer unclean to sight. Advised to have deep cleaned.

17D - adequate ventilation and lighting; designated areas used

Regulation: 511-6-1.07(4)(b) - designated areas for employee activity, located to prevent contamination of food, equipment, utensils, linens, & single service articles (c)

1 ptsCorrected: YesRepeat: No

Observed several personal items stored through out the main kitchen. Cell phones stored on prep top counter, back pack stored on rolling rack. Areas designated for employees to eat, drink, and use tobacco shall be located so that food, equipment, linens, and single-service and single-use articles are protected from contamination. 2. Lockers or other suitable facilities shall be located in a designated room or area where contamination of food, equipment, utensils, linens and single-service and single-use articles cannot occur. COS- all items were moved to personal storage area.

Nov 7, 2023

Routine

Score: 903 violations

4-2B - food-contact surfaces: cleaned & sanitized

Regulation: 511-6-1.05(7)(a)1 - equipment, food-contact surfaces,& utensils (pf)

4 ptsCorrected: YesRepeat: No

Observed both soda guns behind the bar with brown substance built up inside of nozzle. COS- nozzles were removed cleaned and sanitized. Advised to increase cleaning frequency.

4-2B - food-contact surfaces: cleaned & sanitized

Regulation: 511-6-1.05(7)(b) - food contact surfaces and utensils - cleaning frequency (p, c)

4 ptsCorrected: NoRepeat: No

Observed ice scoop handle in direct contact with ice. COS- scoop was removed and placed in dish pit for cleaning.

8-2B - toxic substances properly identified, stored, used

Regulation: 511-6-1.07(6)(g) - chemical sanitizers, criteria (p)

4 ptsCorrected: YesRepeat: Yes

Observed sanitizer bucket in main dinning room reading 200+ Cl. COS- Employees were educated on using test strips to correctly prepare sanitizer bucket and bucket was remade to read 100ppm Cl.