SUBWAY 22761

Observed no ambient thermometers in the walk-in cooler and walk-in freezer. PIC stated one would be placed in each appropriate unit. Rule: 511-6-1.05(2)(x) - TMD, Located in Refrigerators/ Hot Holding (Pf, C) (x) Temperature Measuring Devices.

1. In a mechanically refrigerated or hot food storage unit, the sensor of a temperature measuring device shall be located to measure the air temperature in the warmest part of a mechanically refrigerated unit and in the coolest part of a hot food storage unit.

511-6-1.05(2)(x) - TMD, Located in Refrigerators/ Hot Holding (Pf, C) (x) Temperature Measuring Devices.

1. In a mechanically refrigerated or hot food storage unit, the sensor of a temperature measuring device shall be located to measure the air temperature in the warmest part of a mechanically refrigerated unit and in the coolest part of a hot food storage unit. Note: No ambient thermometers observed in the walk-in cooler and walk-in freezer. PIC stated one would be placed in each appropriate unit.

511-6-1.06(1)(g),(h) - Water Supply, Capacity; Pressure (Pf) (g) Capacity.

1. The water source and system shall be of sufficient capacity to meet the peak water demands of the food service establishment. Pf

2. Hot water generation and distribution systems shall be sufficient to meet the peak hot water demands throughout the food service establishment. Pf Note: Observed water temperature of hand sink in bathroom at 77F. PIC stated maintenance would be contacted to fix hand sink.

11-6-1.07(5)(f) - Drying Mops (C) (f) Drying Mops. After use, mops shall be placed in a position that allows them to air-dry without soiling walls, equipment, or supplies. Note: Observed mops drying in a manner that would not allow for proper air drying. Pic moved mop and placed in a position to allow for proper air drying.

511-6-1.05(6)(n) - Manual and Mechanical Warewashing Equipment, Chemical Sanitization-Temperature, pH, Concentration, Hardness (P,Pf) (n) Manual and Mechanical Warewashing Equipment, Chemical Sanitization - Temperature, pH, Concentration, and Hardness. A chemical sanitizer used in a sanitizing solution for a manual or mechanical operation at contact times specified under subsection (8)(b)3 of this Rule shall meet the requirements specified in DPH Rule 511-6-1-.07(6)(g), shall be used in accordance with the Environmental Protection Agency (EPA)-registered label use instructions P, and shall be used as follows: 3. A quaternary ammonium compound solution shall have a minimum temperature of 75ºF (24ºC), P have a concentration as specified in DPH Rule 511-6-1-.07(6)(g) and as indicated by the manufacturer’s use directions included in the labeling, P and be used only in water with 500 ppm hardness or less or in water having a hardness no greater than specified by the EPA-registered label use instructions

NOTE: Observed no working sanitizer at time of inspection. Employee on line made sanitizer when asked to COS.

511-6-1.05(2)(x) - TMD, Located in Refrigerators/ Hot Holding (Pf, C) (x) Temperature Measuring Devices.

1. In a mechanically refrigerated or hot food storage unit, the sensor of a temperature measuring device shall be located to measure the air temperature in the warmest part of a mechanically refrigerated unit and in the coolest part of a hot food storage unit.

NOTE: Observed no ambient thermometers in the walk in cooler or reach in cooler. PIC to have thermometers ordered to placed in coolers.

511-6-1.03(5)(i) - Hair Restraints (C) (i) Hair Restraints.

1. Employees preparing or handling food shall use effective and clean, disposable or easily cleanable nets or other hair restraints approved by the Health Authority, worn properly to restrain loose hair including beards and mustaches longer than one half inch.

NOTE: Observed employee working on food line without hair restraint. Observed another employee without a beard restraint. PIC COS and had employee place on hat.

Fly strip hanging next to shelf of single service and single use items. Insect control devices may not be located over food prep areas- insect parts could fall and contaminate areas and/or items. Work with pest control operator and health authority for hygienic and effective methods of pest control. .07(2)(m) - Back door to outside has a gap. Outer openings must be solid, self closing and tight fitting. Fix door such that there are no gaps or openings to outside to prevent the entry of pests and insects.