Buena Vida Tapas & Sol

Observed the sanitizer concentration at 0ppm at the dish machine. CA- dish machine must not be used until it is repaired and sanitizer concentration is at 50ppm chlorine. 511-6-1.05(6)(n) - Manual and Mechanical Warewashing Equipment, Chemical Sanitization-Temperature, pH, Concentration, Hardness (P,Pf) (n) Manual and Mechanical Warewashing Equipment, Chemical Sanitization - Temperature, pH, Concentration, and Hardness. A chemical sanitizer used in a sanitizing solution for a manual or mechanical operation at contact times specified under subsection (8)(b)3 of this Rule shall meet the requirements specified in DPH Rule 511-6-1-.07(6)(g), shall be used in accordance with the Environmental Protection Agency (EPA)-registered label use instructions P, and shall be used as follows:

1. A chlorine solution shall have a minimum temperature based on the concentration and pH of the solution as listed in the following chart; P

Concentration Range Minimum Temperature

MG/L PH 10 or less oF (oC) PH 8 or less oF (oC)

25-49 120 (49) 120 (49)

50-99 100 (38) 75 (24)

100 55 (13) 55 (13)

Observed uneasily recognizable seasonings not labeled with the common name. COS- seasonings were labeled. 511-6-1.04(4)(d) - Food Storage Containers Identified with Common Name of Food (C) (d) Food Storage Containers, Identified with Common Name of Food. Except for containers holding food that can be readily and unmistakably recognized, such as dry pasta, working containers holding food or food ingredients that are removed from their original packages for use in the food establishment, such as cooking oils, flour, herbs, potato flakes, salt, spices, and sugar shall be clearly and legibly identified, in English, with the common name of the food.

Observed dishes stacked wet at the time of the inspection. COS- dishes were unstacked to allow air drying. 511-6-1.05(10)(a) - Equipment & Utensils, Air-Drying Required (C) (10) Protection of Clean Items.

(a) Equipment and Utensils, Air-Drying Required. After cleaning and sanitizing, equipment and utensils:

1. Shall be air-dried or used after adequate draining before contact with food; and

2. May not be cloth dried except that utensils that have been air-dried may be polished with cloths that are maintained clean and dry.

Observed debris along countertops and equipment in the main kitchen. CA- all nonfood contact surfaces of equipment shall be cleaned and free of debris. 511-6-1.05(7)(a)2,3 - Equipment, Food/Nonfood-Contact Surfaces, and Utensils, food-contact surfaces of cooking equipment & nonfood-contact surfaces free of accumulations (C) 2. The food-contact surfaces of cooking equipment and pans shall be kept free of encrusted grease deposits and other soil accumulations.

3. Nonfood-contact surfaces of equipment shall be kept free of an accumulation of dust, dirt, food residue, and other debris.

Observed sticker residue and old labels on the outside of the containers that were stored as clean. COS- dishes were taken to be rewashed. 511-6-1.05(7)(d) - Nonfood-Contact Surfaces (C) (d) Nonfood-Contact Surfaces. Nonfood-contact surfaces of equipment shall be cleaned at a frequency necessary to preclude accumulation of soil residues.

Observed no soap at the hand sink in the bar area. CA- soap shall be provided. 511-6-1.07(3)(a) - Handwashing Cleanser, Availability (Pf) (3) Numbers and Capacities.

(a) Handwashing Cleanser, Availability. Each handwashing sink or group of two adjacent handwashing sinks shall be provided with a supply of hand cleaning liquid, powder, or bar soap. Pf

Observed no paper towels at the hand sink in the bar area. COS- paper towels provided. 511-6-1.07(3)(b) - Hand Drying Provision (Pf) (b) Hand Drying Provision. Each handwashing sink or group of adjacent handwashing sinks shall be provided with:

1. Individual, disposable towels; Pf

2. A continuous towel system that supplies the user with a clean towel; Pf

3. A heated-air hand drying device; Pf or

4. A hand drying device that employs an air-knife system that delivers high velocity, pressurized air at ambient temperatures.Pf

Observed a knife stored in the hand sink in the main kitchen, observed a chemical bottle stored in the second hand sink in the kitchen. COS- items were removed from sink. 511-6-1.06(2)(o) - Using a Handwashing Sink- Operation & maintenance (Pf) (o) Using a Handwashing Sink.

1. A handwashing sink shall be maintained so that it is accessible at all times for employee use. Pf

2. A handwashing facility may not be used for purposes other than handwashing. Pf

3. An automatic handwashing facility shall be used in accordance with manufacturer’s instructions. Pf

Observed uneasily recognizable seasonings not labeled with the common name. COS- seasonings were labeled. 511-6-1.04(4)(d) - Food Storage Containers Identified with Common Name of Food (C) (d) Food Storage Containers, Identified with Common Name of Food. Except for containers holding food that can be readily and unmistakably recognized, such as dry pasta, working containers holding food or food ingredients that are removed from their original packages for use in the food establishment, such as cooking oils, flour, herbs, potato flakes, salt, spices, and sugar shall be clearly and legibly identified, in English, with the common name of the food.

Observed salmon thawed in the vacuum packaging that beared a warning label to remove. COS- salmon was removed from packaging. 511-6-1.04(6)(c) - Thawing (C) (c) Thawing. Except as specified in paragraph 4 of this subsection, time/temperature control for safety food shall be thawed: 5. Reduced oxygen packaged fish that bears a label indicating that it is to be kept frozen until time of use shall be removed from the reduced oxygen environment:

(i) Prior to its thawing under refrigeration that maintains the food temperature at 41°F (5°C) or less; or

(ii) Prior to, or immediately upon completion of its thawing, using procedures to completely submerge in running water as specified in paragraph 2 of this subsection.

Observed the most recent inspection report not posted. Ca- inspection received via email today shall be printed and posted. 511-6-1.02(1)(d) - Displaying of the Inspection Report (C)

1. The most current inspection report shall be prominently displayed in public view at all times, within fifteen feet of the front or primary public door and between five feet and seven feet from the floor and in an area where it can be read at a distance of one foot away.

Observed no hand washing sign at the designated hand sink in the bar area. CA- hand sink sign shall be posted to designate sink. 511-6-1.07(3)(d) - Handwashing Signage (C) (d) Handwashing Signage. A sign or poster that notifies food employees to wash their hands shall be provided at all handwashing sinks used by food employees and shall be clearly visible to food employees.

Observed the prep top cooler cutting boards stained and with gashes. CA- cutting boards shall be replaced or resurfaced. 511-6-1.05(6)(b) - Cutting Surfaces (C) (b) Cutting Surfaces. Surfaces such as cutting blocks and boards that are subject to scratching and scoring shall be resurfaced if they can no longer be effectively cleaned and sanitized, or discarded if they cannot be resurfaced.

Observed no lactic acid test strips for the sink and surface cleaner. CA-PIC must order lactic acid test strips. 511-6-1.05(3)(h),(i),(j) - Temperature Measuring Device, Manual Warewashing; Sanitizing Solutions, Testing Device (Pf) (h) Temperature Measuring Devices, Manual and Mechanical Warewashing.

1. In manual warewashing operations, a temperature measuring device shall be provided and readily accessible for frequently measuring the washing and sanitizing temperatures. Pf

2. In hot water mechanical warewashing operations, an irreversible registering temperature indicator shall be provided and readily accessible for measuring the utensil surface temperature. Pf

(i) Sanitizing Solutions, Testing Devices. A test kit or other device that accurately measures the concentration in mg/L of sanitizing solutions shall be provided. Pf

j) Cleaning Agents and Sanitizers.

1. Cleaning agents that are used to clean equipment and utensils as specified under section (7) of this Rule, shall be provided and available for use during all hours of operation. Pf

2. Except for those that are generated on-site at the time of use, chemical sanitizers that are used to sanitize equipment and utensils, as specified under Section (8) of this Rule, shall be provided and available for use during all hours of operation. Pf

Observed mash potatoes, cooked duck, and cooked rice stored in a RIC without being date marked. COS- PIC date marked the food as it was made yesterday. 511-6-1.04(6)(g) - Ready-To-Eat Time/Temperature Control for Safety Food, Date Marking (Pf) (g) Ready-to-Eat Time/Temperature Control for Safety Food, Date Marking

1. Except when packaging food using a reduced oxygen packaging method, and except as specified in paragraphs 5 and 6 of this subsection, refrigerated, ready-to-eat, time/temperature control for safety food prepared and held in a food establishment for more than 24 hours shall be clearly marked to indicate the date or day by which the food shall be consumed on the premises, sold, or discarded, when held at a temperature of 41°F (5°C) or below for a maximum of 7 days. The day of preparation shall be counted as Day 1. Pf

2. Except as specified in paragraphs 5 through 7 of this subsection, refrigerated, ready-to-eat, time/temperature control for safety food prepared and packaged by a food processing plant shall be clearly marked, at the time the original container is opened in a food service establishment and if the food is held for more than 24 hours, to indicate the date or day by which the food shall be consumed on the premises, sold, or discarded, when held at a temperature of 41°F (5°C) or below for a maximum of 7 days after the original container is opened. The day the original container is opened in the food service establishment shall be counted as Day 1, except, the day or date marked by the food service establishment may not exceed a manufacturer’s use by date if the manufacturer determined the use-by date based on food safety; Pf

3. A refrigerated, ready-to-eat, time/temperature control for safety food ingredient or a portion of a refrigerated, ready-to-eat, time/temperature control for safety food that is subsequently combined with additional ingredients or portions of food shall retain the date marking of the earliest-prepared or first-prepared ingredient. Pf

4. A date marking system that meets the criteria stated in paragraphs 1 and 2 of this subsection may include:

(i) Using a method approved by the Health Authority for refrigerated, ready-to-eat time / temperature control for safety food that is frequently rewrapped, such as lunchmeat or a roast, or for which date marking is impractical, such as soft serve mix or milk in a dispensing machine;

(ii) Marking the date or day of preparation, with a procedure to discard the food on or before the last date or day by which the food must be consumed on the premises, sold, or discarded;

(iii) Marking the date or day the original container is opened in a food service establishment, with a procedure to discard the food on or before the last date or day by which the food must be consumed on the premises, sold, or discarded; or

(iv) Using calendar dates, days of the week, color-coded marks, or other effective marking methods, provided that the marking system is disclosed to the Health Authority upon request.

5. The requirements in paragraphs 1 and 2 of this subsection do not apply to individual meal portions served or repackaged for sale from a bulk container upon a consumer’s request.

6. The requirements in paragraphs 1 and 2 of this subsection do not apply to shellstock.

7. The requirement in paragraph 2 of this subsection does not apply to the following foods prepared and packaged by a food processing plant inspected by a Health Authority:

(i) Deli salads, such as ham salad, seafood salad, chicken salad, egg salad, pasta salad, potato salad, and macaroni salad, manufactured in accordance with 21 CFR 117 Current good manufacturing practice in manufacturing, packing, or holding human food;

(ii) Hard cheeses containing not more than 39% moisture as defined in 21 CFR 133 Cheeses and related cheese products, such as cheddar, gruyere, parmesan and reggiano, and romano;

(iii) Semi-soft cheeses containing more than 39% moisture, but not more than 50% moisture, as defined in 21 CFR 133 Cheeses and related cheese products, such as blue, edam, gorgonzola, gouda, and monterey jack;

(iv) Cultured dairy products as defined in 21 CFR 131 Milk and cream, such as yogurt, sour cream, and buttermilk;

(v) Preserved fish products, such as pickled herring and dried or salted cod, and other acidified fish products defined in 21 CFR 114 Acidified foods;

(vi) Shelf stable, dry fermented sausages, such as pepperoni and Genoa salami; and

Observed a large deep container of grits cooling at room temperature. COS- grits were moved into a shallow pan and placed on ice bath to start the cooling process. 511-6-1.04(6)(e) - Cooling Methods (Pf, C) (e) Cooling Methods.

1. Cooling shall be accomplished in accordance with the time and temperature criteria specified under DPH Rule 511-6-1-.04(6)(d) by using one or more of the following methods depending on the type of food being cooled:

(i) Placing the food in shallow pans; Pf

(ii) Separating the food into smaller or thinner portions; Pf

(iii) Using rapid cooling equipment; Pf

(iv) Stirring the food in a container placed in an ice water bath; Pf

(v) Using containers that facilitate heat transfer; Pf

(vi) Adding ice as an ingredient; Pf or

(vii) Other effective methods. Pf

2. When placed in cooling or cold holding equipment, food containers in which food is being cooled shall be:

(i) Arranged in the equipment to provide maximum heat transfer through the container walls; and

(ii) Loosely covered, or uncovered if protected from overhead contamination during the cooling period to facilitate heat transfer from the surface of the food.

Observed ice scoops stored inside the ice bucket with the school handle touching the ice. COS- ice scoops were moved to a clean surface. 511-6-1.04(4)(k) - In-Use Utensils, Between-Use Storage (C) (k)Storage of In-Use Utensils. During pauses in food preparation or dispensing, food preparation and dispensing utensils shall be stored:

1.Except as specified under paragraph 2 of this subsection, in the food with their handles above the top of the food and the container;

2.In food that is not time/temperature control for safety food with their handles above the top of the food within containers or equipment that can be closed, such as bins of sugar, flour, or cinnamon;

3.On a clean portion of the food preparation table or cooking equipment only if the in-use utensil and the food-contact surface of the food preparation table or cooking equipment are cleaned and sanitized at a frequency specified under DPH Rule 511-6-1-.05(7)(b) and (8)(a);

4.In running water of sufficient velocity to flush particulates to the drain, if used with moist food such as ice cream or mashed potatoes;

5. In a clean, protected location if the utensils, such as ice scoops, are used only with a food that is not time/temperature control for safety food; or

6. In a container of water if the water is maintained at a temperature of at least 135°F (57°C) and the container is cleaned at a frequency specified under DPH Rule 511-6-1-.05(7)(b)3(vi).

Observed dishes stacked wet. COS- dishes were rewashed. 511-6-1.05(10)(a) - Equipment & Utensils, Air-Drying Required (C) (10) Protection of Clean Items.

(a) Equipment and Utensils, Air-Drying Required. After cleaning and sanitizing, equipment and utensils:

1. Shall be air-dried or used after adequate draining before contact with food; and

2. May not be cloth dried except that utensils that have been air-dried may be polished with cloths that are maintained clean and dry.

Observed the prep top cooler cutting boards stained and with gashes. CA- cutting boards shall be replaced or resurfaced. 511-6-1.05(6)(b) - Cutting Surfaces (C) (b) Cutting Surfaces. Surfaces such as cutting blocks and boards that are subject to scratching and scoring shall be resurfaced if they can no longer be effectively cleaned and sanitized, or discarded if they cannot be resurfaced.

Observed no lactic acid test strips for the sink and surface cleaner. CA-PIC must order lactic acid test strips. 511-6-1.05(3)(h),(i),(j) - Temperature Measuring Device, Manual Warewashing; Sanitizing Solutions, Testing Device (Pf) (h) Temperature Measuring Devices, Manual and Mechanical Warewashing.

1. In manual warewashing operations, a temperature measuring device shall be provided and readily accessible for frequently measuring the washing and sanitizing temperatures. Pf

2. In hot water mechanical warewashing operations, an irreversible registering temperature indicator shall be provided and readily accessible for measuring the utensil surface temperature. Pf

(i) Sanitizing Solutions, Testing Devices. A test kit or other device that accurately measures the concentration in mg/L of sanitizing solutions shall be provided. Pf

j) Cleaning Agents and Sanitizers.

1. Cleaning agents that are used to clean equipment and utensils as specified under section (7) of this Rule, shall be provided and available for use during all hours of operation. Pf

2. Except for those that are generated on-site at the time of use, chemical sanitizers that are used to sanitize equipment and utensils, as specified under Section (8) of this Rule, shall be provided and available for use during all hours of operation. Pf

Observed debris on the gaskets inside the coolers. CA- cooler gaskets shall be cleaned. 511-6-1.05(7)(d) - Nonfood-Contact Surfaces (C) (d) Nonfood-Contact Surfaces. Nonfood-contact surfaces of equipment shall be cleaned at a frequency necessary to preclude accumulation of soil residues.

Observed multiple containers stored as clean with old labels attached on the outside of the containers. COS- dishes were rewashed and labels removed. 511-6-1.05(7)(a)2,3 - Equipment, Food/Nonfood-Contact Surfaces, and Utensils, food-contact surfaces of cooking equipment & nonfood-contact surfaces free of accumulations (C) 2. The food-contact surfaces of cooking equipment and pans shall be kept free of encrusted grease deposits and other soil accumulations.

3. Nonfood-contact surfaces of equipment shall be kept free of an accumulation of dust, dirt, food residue, and other debris.

Observed no vomit/fecal kit and materials to respond to vomit/fecal events. Advised PIC to obtain vomit/fecal kit. PIC ordered new vomit/fecal kit during inspection.

Observed black and pink build up long food contact surface of ice machine. Advised PIC to dump ice and clean to sight and touch.

Observed multiple TCS foods intended for cold holding, held at temperatures above 41F. Advised PIC to relocate food and explained how to do correct ice bath for food. COS- PIC corrected all ice baths.