May 27, 2026
Routine
2-1B - hands clean and properly washed
Regulation: 511-6-1.03(5)(c) - when to wash (p)
Observed employee failure to change gloves and wash hands after returning to kitchen. CA: PIC educated employee on proper handwashing procedures when returning to kitchen. Employee changed gloves and washed hands during inspection. 511-6-1.03(5)(c) - When to Wash (P) (c) When to Wash.
- Food employees shall clean their hands and exposed portions of their arms immediately before engaging in food preparation including working with exposed food, clean equipment and utensils, and unwrapped single-service and single-use articles P and:
(i) After touching bare human body parts other than clean hands and clean, exposed arms; P
(ii) After using the toilet room; P
(iii) After caring for or handling service animals or aquatic animals; P
(iv) After coughing, sneezing, using a handkerchief or disposable tissue, using tobacco products or electronic devices that simulate tobacco smoking, eating or drinking, except for drinking from a closed beverage container and the container is handled to prevent contamination of the hands;P
(v) After handling soiled equipment or utensils; P
(vi) During food preparation, as often as necessary to remove soil and contamination and to prevent cross contamination when changing tasks; P
(vii) When switching between working with raw food and working with ready-to-eat food; P
(viii) Before donning gloves to initiate a task that involves working with food; P and
(ix) After engaging in other activities that contaminate the hands. P
- All employees shall wash hands before leaving the restroom. All food employees leaving the restroom shall wash their hands again upon re-entering the food preparation area. P
6-2 - proper date marking and disposition
Regulation: 511-6-1.04(6)(g) - ready-to-eat time/temperature control for safety food, date marking (pf)
Observed cooked beef lasagna prepared on 5/19/26, held more than 7 days stored on shelf in walk in cooler. CA: PIC discarded cooked beef lasagna during inspection. 511-6-1.04(6)(g) - Ready-To-Eat Time/Temperature Control for Safety Food, Date Marking (Pf) (g) Ready-to-Eat Time/Temperature Control for Safety Food, Date Marking
- Except when packaging food using a reduced oxygen packaging method, and except as specified in paragraphs 5 and 6 of this subsection, refrigerated, ready-to-eat, time/temperature control for safety food prepared and held in a food establishment for more than 24 hours shall be clearly marked to indicate the date or day by which the food shall be consumed on the premises, sold, or discarded, when held at a temperature of 41°F (5°C) or below for a maximum of 7 days. The day of preparation shall be counted as Day 1. Pf
18 - insects, rodents, and animals not present
Regulation: 511-6-1.07(5)(k) - controlling pests (pf, c)
Observed 4-5 live gnats near soda syrup dispenser in kitchen. CA: Informed operator of live gnats, gnats were removed and areas disinfected during inspection. 511-6-1.07(5)(k) - Controlling Pests (Pf, C) (k) Controlling Pests. The presence of insects, rodents, and other pests shall be controlled to minimize their presence on the premises by:
-
Routinely inspecting incoming shipments of food and supplies;
-
Routinely inspecting the premises for evidence of pests;
-
Using methods, if pests are found, such as trapping devices or other means of pest control as specified under subsections (6)(e), (6)(m), and (6)(n) of this Rule; Pf and
-
Eliminating harborage conditions.
17C - physical facilities installed, maintained, and clean
Regulation: 511-6-1.07(2)(a) - floor, walls, & ceilings, cleanability (c)
Observed multiple cracked and missing tiles throughout cookline, ware wash area, food preparation area and walk in cooler in kitchen. CA: Operator must repair/replace broken and missing tiles within 10 days. 511-6-1.07(2)(a) - Floor, Walls, & Ceilings, Cleanability (C) (2) Design, Construction, and Installation.
(a) Floors, Walls, and Ceilings, Cleanability. Except as specified under subsection (2)(d) of this Rule and except for antislip floor coverings or applications that may be used for safety reasons, floors, floor coverings, walls, wall coverings, and ceilings shall be designed, constructed, and installed so they are smooth and easily cleanable.