DOWNTOWN CAFE & PIZZARIA

511-6-1.05(7)(b) - Food Contact Surfaces and Utensils - Cleaning Frequency (P, C) (b) Equipment Food-Contact Surfaces and Utensils.

1. Equipment food-contact surfaces and utensils shall be cleaned: (iv) In equipment such as ice bins and beverage dispensing nozzles and enclosed components of equipment such as ice makers, cooking oil storage tanks and distribution lines, beverage and syrup dispensing lines or tubes, coffee bean grinders, and water vending equipment:

(I) At a frequency specified by the manufacturer; or

(II) Absent manufacturer specifications, at a frequency necessary to preclude accumulation of soil or mold. Note: Observed mold-like accumulation on ice machine chute. PIC to wash rinse and sanitize machine by end of business.

511-6-1.04(6)(e) - Cooling Methods (Pf, C) (e) Cooling Methods.

1. Cooling shall be accomplished in accordance with the time and temperature criteria specified under DPH Rule 511-6-1-.04(6)(d) by using one or more of the following methods depending on the type of food being cooled:

(i) Placing the food in shallow pans; Pf

(ii) Separating the food into smaller or thinner portions; Pf

(iii) Using rapid cooling equipment; Pf

(iv) Stirring the food in a container placed in an ice water bath; Pf

(v) Using containers that facilitate heat transfer; Pf

(vi) Adding ice as an ingredient; Pf or

(vii) Other effective methods. Pf

2. When placed in cooling or cold holding equipment, food containers in which food is being cooled shall be:

(i) Arranged in the equipment to provide maximum heat transfer through the container walls; and

(ii) Loosely covered, or uncovered if protected from overhead contamination during the cooling period to facilitate heat transfer from the surface of the food. Note: Observed pasta in large container cooling in WIC fully covered not allowing for proper heat transfer. PIC uncovered container to allow for proper cooling.

511-6-1.05(6)(n) - Manual and Mechanical Warewashing Equipment, Chemical Sanitization-Temperature, pH, Concentration, Hardness (P,Pf) (n) Manual and Mechanical Warewashing Equipment, Chemical Sanitization - Temperature, pH, Concentration, and Hardness. A chemical sanitizer used in a sanitizing solution for a manual or mechanical operation at contact times specified under subsection (8)(b)3 of this Rule shall meet the requirements specified in DPH Rule 511-6-1-.07(6)(g), shall be used in accordance with the Environmental Protection Agency (EPA)-registered label use instructions P, and shall be used as follows: Note: Facility's bar dish machine registered 10ppm Chlorine. PIC contacted EcoLab to come out and fix it. In the meantime facility will not use dish machine at bar and instead use the dish machine in the main kitchen.

511-6-1.04(4)(k) - In-Use Utensils, Between-Use Storage (C) (k)Storage of In-Use Utensils. During pauses in food preparation or dispensing, food preparation and dispensing utensils shall be stored:

1.Except as specified under paragraph 2 of this subsection, in the food with their handles above the top of the food and the container;

2.In food that is not time/temperature control for safety food with their handles above the top of the food within containers or equipment that can be closed, such as bins of sugar, flour, or cinnamon; Note: Observed a bowl without a handle being used as a scoop in for flour container. PIC removed bowl and replaced it with an approved scoop with a handle.

511-6-1.05(3)(h),(i) - Temperature Measuring Device, Manual Warewashing; Sanitizing Solutions, Testing Device (Pf) (i) Sanitizing Solutions, Testing Devices. A test kit or other device that accurately measures the concentration in mg/L of sanitizing solutions shall be provided. Pf Note: Facility did not have test strips to test the concentration of the chlorine in their dishmachines. PIC stated he would purchase some as soon as possible.