College Park, Fulton County

Cheese Me Please Me ATL

5015 OLD NATIONAL HWY STE G ATLANTA, GA 30349

Food
Latest score
80
Feb 23, 2026
City
College Park
County
Fulton
Inspections
5

Score history

Inspection scores over time for this facility.

Inspection history

Georgia inspection history is score-based, with violations grouped under each recorded inspection.

Feb 23, 2026

Followup

Score: 809 violations

6-1A - proper cold holding temperatures

Regulation: 511-6-1.04(6)(f) - time/temperature control for safety; cold holding (p)

9 ptsCorrected: NoRepeat: No

Observed potentially hazardous foods (salmon and shrimp) cold held in prep top cooler at greater than 41 degrees Fahrenheit.

511-6-1.04(6)(f) - Time/Temperature Control for Safety; Cold Holding (P) (f) Time/Temperature Control for Safety Food, Hot and Cold Holding. Except during preparation, cooking, or cooling, or when time is used as the public health control, time/temperature control for safety food shall be maintained at 41°F (5°C) or below or 135°F (57°C) or above, except that roasts cooked to a temperature and for a time specified in subsection (5)(a)2 of this Rule and reheated using the same temperature and time conditions as cooking may be held at a temperature of 130°F (54°C) or above. P

2-2D - adequate handwashing facilities supplied & accessible

Regulation: 511-6-1.06(2)(o) - using a handwashing sink- operation & maintenance (pf)

4 ptsCorrected: YesRepeat: No

Observed Handwash sink not accessible for employee use at all times (red bucket and plastic containers stored in hand sink. Mop bucket in front of hand sink.

511-6-1.06(2)(o) - Using a Handwashing Sink- Operation & maintenance (Pf) (o) Using a Handwashing Sink.

  1. A handwashing sink shall be maintained so that it is accessible at all times for employee use. Pf

  2. A handwashing facility may not be used for purposes other than handwashing. Pf

  3. An automatic handwashing facility shall be used in accordance with manufacturer’s instructions. Pf

12C - wiping cloths: properly used and stored

Regulation: 511-6-1.04(4)(m) - wiping cloths, use limitation (c)

3 ptsCorrected: NoRepeat: No

Wet wiping cloth not stored in sanitizing solution between uses.

511-6-1.04(4)(m) - Wiping Cloths, Use Limitation (C) (m) Wiping Cloths, Use Limitation.

  1. Cloths in-use for wiping food spills from tableware and carry-out containers that occur as food is being served shall be:

(i) Maintained dry; and

(ii) Used for no other purpose.

  1. Cloths in-use for wiping counters and other equipment surfaces shall be:

(i) Held between uses in a chemical sanitizer solution at a concentration specified under DPH Rule 511-6-1-.05(6)(n); and

(ii) Laundered daily.

  1. Cloths in-use for wiping surfaces in contact with raw animal foods shall be kept separate from cloths used for other purposes.

  2. Dry wiping cloths and the chemical sanitizing solutions in which wet wiping cloths are held between uses shall be free of food debris and visible soil.

  3. Containers of chemical sanitizing solutions in which wet wiping cloths are held between uses shall be stored off the floor and used in a manner that prevents contamination of food, equipment, utensils, linens, single-service, or single-use articles.

16B - plumbing installed; proper backflow devices

Regulation: 511-6-1.06(2)(r) - system maintained in good repair (p, c)

2 ptsCorrected: NoRepeat: No

Observed leaking pipe at plumbing fixture at the 3 compartment faucet and the water handle of the prep sink.

511-6-1.06(2)(r) - System Maintained in Good Repair (P, C) (r) System Maintained in Good Repair. A plumbing system shall be repaired according to law; P and maintained in good repair.

15C - nonfood-contact surfaces clean

Regulation: 511-6-1.05(7)(d) - nonfood-contact surfaces (c)

1 ptsCorrected: NoRepeat: No

Observed the Reach-in cooler not cleaned to prevent accumulation of soil residue.

511-6-1.05(7)(d) - Nonfood-Contact Surfaces (C) (d) Nonfood-Contact Surfaces. Nonfood-contact surfaces of equipment shall be cleaned at a frequency necessary to preclude accumulation of soil residues.

15C - nonfood-contact surfaces clean

Regulation: 511-6-1.05(7)(d) - nonfood-contact surfaces (c)

1 ptsCorrected: NoRepeat: No

Observed the outside of prep top cooler doors not cleaned to prevent accumulation of soil residue.

511-6-1.05(7)(d) - Nonfood-Contact Surfaces (C) (d) Nonfood-Contact Surfaces. Nonfood-contact surfaces of equipment shall be cleaned at a frequency necessary to preclude accumulation of soil residues.

17A - toilet facilities: properly constructed, supplied, cleaned

Regulation: 511-6-1.07(2)(l) - toilet rooms, enclosed (c)

1 ptsCorrected: NoRepeat: No

Bathroom not enclosed with tight-fitting, self-closing doors.

511-6-1.07(2)(l) - Toilet Rooms, Enclosed (C) (l) Toilet Rooms, Enclosed. Except where a toilet room is located outside a food service establishment and does not open directly into the food service establishment, such as a toilet room that is provided by the management of a shopping mall, a toilet room located on the premises shall be completely enclosed and provided with a tight-fitting and self-closing door.

17C - physical facilities installed, maintained, and clean

Regulation: 511-6-1.07(2)(f),(g) - wall & ceiling coverings & coatings; wall & ceiling attachments (c)

1 ptsCorrected: NoRepeat: No

Observe missing Ceiling tile missing. Inside restroom and damaged ceiling above dry storage area.

511-6-1.07(2)(f),(g) - Wall & Ceiling Coverings & Coatings; Wall & Ceiling Attachments (C) (f) Wall and Ceiling Coverings and Coatings.

  1. Wall and ceiling covering materials shall be nonabsorbent, light colored, and attached so that they are easily cleanable.

  2. Except in areas used only for dry storage, concrete, porous blocks, or bricks used for indoor wall construction shall be finished and sealed to provide a smooth, nonabsorbent, easily cleanable surface.

(g) Walls and Ceiling, Attachments.

  1. Except as specified in paragraphs 2 of this subsection, attachments to walls and ceilings such as light fixtures, mechanical room ventilation system components, vent covers, wall mounted fans, decorative items, and other attachments shall be easily cleanable.

  2. In a consumer area, wall and ceiling surfaces and decorative items and attachments that are provided for ambiance need not meet this requirement if they are kept clean.

17D - adequate ventilation and lighting; designated areas used

Regulation: 511-6-1.07(2)(j) - heating, ventilation, air conditioning, system vents, designed to prevent contamination (c)

1 ptsCorrected: NoRepeat: No

Observed missing Light shield and vent covers missing in ceiling above dishwashing and dry storage area.

. 511-6-1.07(2)(j) - Heating, Ventilation, Air Conditioning, System Vents, designed to prevent contamination (C) (j) Heating, Ventilating, Air Conditioning, System Vents. Heating, ventilating, and air conditioning systems shall be designed and installed so that make-up air intake and exhaust vents do not cause contamination of food, food-contact surfaces, equipment, or utensils.

Feb 11, 2026

Routine

Score: 7616 violations

6-1A - proper cold holding temperatures

Regulation: 511-6-1.04(6)(f) - time/temperature control for safety; cold holding (p)

9 ptsCorrected: YesRepeat: Yes

Observed potentially hazardous food cold held (chicken, shrimp and salmon) at greater than 41 degrees Fahrenheit inside the Large prep top cooler.

CA: Food items discarded by PIC also the certified food safety manager was notified

511-6-1.04(6)(f) - Time/Temperature Control for Safety; Cold Holding (P) (f) Time/Temperature Control for Safety Food, Hot and Cold Holding. Except during preparation, cooking, or cooling, or when time is used as the public health control, time/temperature control for safety food shall be maintained at 41°F (5°C) or below or 135°F (57°C) or above, except that roasts cooked to a temperature and for a time specified in subsection (5)(a)2 of this Rule and reheated using the same temperature and time conditions as cooking may be held at a temperature of 130°F (54°C) or above. P

6-1B - proper hot holding temperatures

Regulation: 511-6-1.04(6)(f) - time/temperature control for safety; hot holding (p)

9 ptsCorrected: NoRepeat: No

Observed hot potentially hazardous food (large container of yellow rice) held at less than 135 degrees Fahrenheit on table in main kitchen

10D - food properly labeled; original container

Regulation: 511-6-1.04(7)(c) - food labels (pf, c)

3 ptsCorrected: NoRepeat: No

Food being packaged in the food service establishment were not labeled as per the labeling requirements in 511-6-1-.04(7)(c)1-4.

511-6-1.04(7)(c) - Food Labels (Pf, C) (c) Food Labels.

  1. Food packaged in a food service establishment, that is not provided by a foodservice employee upon consumer request, shall be labeled as specified in law, including 21 CFR 101- Food labeling, and 9 CFR 317 Labeling, marking devices, and containers.

  2. Label information shall include:

(i) The common name of the food, or if there is no common name, an adequately descriptive identity statement;

(ii) If made from two or more ingredients, a list of ingredients and sub-ingredients in descending order of predominance by weight, including a declaration of artificial color or flavors and chemical preservatives, if contained in the food;

(iii) An accurate declaration of the net quantity of contents;

(iv) The name and place of business of the manufacturer, packer, or distributor; and

(v) The name of the food source for each major food allergen contained in the food unless the food source is already part of the common or usual name of the respective ingredient. Pf

(vi) Except as exempted in the Federal Food, Drug, and Cosmetic Act § 403(Q)(3) - (5), nutrition labeling as specified in 21 CFR 101 - Food Labeling and 9 CFR 317 Subpart B Nutrition Labeling.

(vii) For any salmonid fish containing canthaxanthin or astaxanthin as a color additive, the labeling of the bulk fish container, including a list of ingredients, displayed on the retail container or by other written means, such as a counter card, that discloses the use of canthaxanthin or astaxanthin.

  1. Bulk food that is available for consumer self-dispensing shall be prominently labeled with the following information in plain view of the consumer:

(i) The manufacturer's or processor's label that was provided with the food; or

(ii) A card, sign, or other method of notification that includes the information specified under paragraphs 2(i), (ii), (v) and (vi) of this subsection.

  1. Bulk, unpackaged foods such as bakery products and unpackaged foods that are portioned to consumer specification need not be labeled if:

(i) A health, nutrient content, or other claim is not made;

(ii) There are no state or local laws requiring labeling; and

(iii) The food is manufactured or prepared on the premises of the food service establishment or at another food service establishment or a food processing plant that is owned by the same person and is regulated by the food regulatory agency that has jurisdiction.

12C - wiping cloths: properly used and stored

Regulation: 511-6-1.04(4)(m) - wiping cloths, use limitation (c)

3 ptsCorrected: YesRepeat: No

Wiping cloth chlorine sanitizing solution not at proper minimum strength.

511-6-1.04(4)(m) - Wiping Cloths, Use Limitation (C) (m) Wiping Cloths, Use Limitation.

COS: Person in charge corrected level on sanitizer and place some bleach in sanitizing bucket

16B - plumbing installed; proper backflow devices

Regulation: 511-6-1.06(2)(r) - system maintained in good repair (p, c)

2 ptsCorrected: NoRepeat: No

Observed leaking pipe at plumbing fixture at the faucet of the three compartment sink and at the cold water handle of the prep sink.

511-6-1.06(2)(r) - System Maintained in Good Repair (P, C) (r) System Maintained in Good Repair. A plumbing system shall be repaired according to law; P and maintained in good repair.

16B - plumbing installed; proper backflow devices

Regulation: 511-6-1.06(2)(e) - backflow prevention device, design standard (p)

2 ptsCorrected: NoRepeat: No

Observed no backflow device on mop sink.

511-6-1.06(2)(e) - Backflow Prevention Device, Design Standard (P) (e) Backflow Prevention Device, Design Standard. A backflow or backsiphonage prevention device installed on a water supply system shall meet American Society of Sanitary Engineering (A.S.S.E.) standards for construction, installation, maintenance, inspection, and testing for that specific application and type of device. P

CA: Provide a backflow device on the faucet of the mop sink within 30 days.

17A - toilet facilities: properly constructed, supplied, cleaned

Regulation: 511-6-1.07(2)(l) - toilet rooms, enclosed (c)

1 ptsCorrected: NoRepeat: No

Bathroom not enclosed with tight-fitting, self-closing doors.

511-6-1.07(2)(l) - Toilet Rooms, Enclosed (C) (l) Toilet Rooms, Enclosed. Except where a toilet room is located outside a food service establishment and does not open directly into the food service establishment, such as a toilet room that is provided by the management of a shopping mall, a toilet room located on the premises shall be completely enclosed and provided with a tight-fitting and self-closing door.

17C - physical facilities installed, maintained, and clean

Regulation: 511-6-1.07(2)(f),(g) - wall & ceiling coverings & coatings; wall & ceiling attachments (c)

1 ptsCorrected: NoRepeat: Yes

Ceiling tiles missing inside restroom and damaged ceiling tiles in dry storage area.

511-6-1.07(2)(f),(g) - Wall & Ceiling Coverings & Coatings; Wall & Ceiling Attachments (C) (f) Wall and Ceiling Coverings and Coatings.

  1. Wall and ceiling covering materials shall be nonabsorbent, light colored, and attached so that they are easily cleanable.

  2. Except in areas used only for dry storage, concrete, porous blocks, or bricks used for indoor wall construction shall be finished and sealed to provide a smooth, nonabsorbent, easily cleanable surface.

(g) Walls and Ceiling, Attachments.

  1. Except as specified in paragraphs 2 of this subsection, attachments to walls and ceilings such as light fixtures, mechanical room ventilation system components, vent covers, wall mounted fans, decorative items, and other attachments shall be easily cleanable.

  2. In a consumer area, wall and ceiling surfaces and decorative items and attachments that are provided for ambiance need not meet this requirement if they are kept clean.

17D - adequate ventilation and lighting; designated areas used

Regulation: 511-6-1.07(2)(i) - light bulbs, protective shielding (c)

1 ptsCorrected: NoRepeat: No

Observed missing light shield in back storage area above dry storage and clean equipment rack.

511-6-1.07(2)(i) - Light Bulbs, Protective Shielding (C) (i) Light Bulbs, Protective Shielding.

  1. Except as specified in paragraph 2 of this subsection, light bulbs shall be shielded, coated, or otherwise shatter-resistant in areas where there is exposed food; clean equipment, utensils, and linens; or unwrapped single-service and single-use articles.

  2. Shielded, coated, or otherwise shatter-resistant bulbs need not be used in areas used only for storing food in unopened packages, if:

(i) The integrity of the packages cannot be affected by broken glass falling onto them; and

(ii) The packages are capable of being cleaned of debris from broken bulbs before the packages are opened.

  1. An infrared or other heat lamp shall be protected against breakage by a shield surrounding and extending beyond the bulb so that only the face of the bulb is exposed.

17D - adequate ventilation and lighting; designated areas used

Regulation: 511-6-1.07(2)(j) - heating, ventilation, air conditioning, system vents, designed to prevent contamination (c)

1 ptsCorrected: NoRepeat: No

Observed missing air conditioning/ventilation vent covers above dish washing area.

511-6-1.07(2)(j) - Heating, Ventilation, Air Conditioning, System Vents, designed to prevent contamination (C) (j) Heating, Ventilating, Air Conditioning, System Vents. Heating, ventilating, and air conditioning systems shall be designed and installed so that make-up air intake and exhaust vents do not cause contamination of food, food-contact surfaces, equipment, or utensils.

13A - posted: permit/inspection/choking poster/handwashing

Regulation: 511-6-1.02(1)(d) - displaying of the inspection report (c)

1 ptsCorrected: NoRepeat: No

The most current inspection report is not posted. Observed an old inspection posted from 2023.

511-6-1.02(1)(d) - Displaying of the Inspection Report (C)

  1. The most current inspection report shall be prominently displayed in public view at all times, within fifteen feet of the front or primary public door and between five feet and seven feet from the floor and in an area where it can be read at a distance of one foot away.

14A - in-use utensils: properly stored

Regulation: 511-6-1.04(4)(k) - in-use utensils, between-use storage (c)

1 ptsCorrected: NoRepeat: No

Observed ice cream scoop stored in standing water less than 135 degrees Fahrenheit.

511-6-1.04(4)(k) - In-Use Utensils, Between-Use Storage (C) (k)Storage of In-Use Utensils. During pauses in food preparation or dispensing, food preparation and dispensing utensils shall be stored: 4.In running water of sufficient velocity to flush particulates to the drain, if used with moist food such as ice cream or mashed potatoes;

  1. In a clean, protected location if the utensils, such as ice scoops, are used only with a food that is not time/temperature control for safety food; or

  2. In a container of water if the water is maintained at a temperature of at least 135°F (57°C) and the container is cleaned at a frequency specified under DPH Rule 511-6-1-.05(7)(b)3(vi).

14B - utensils, equipment and linens: properly stored, dried, handled

Regulation: 511-6-1.05(10)(a) - equipment & utensils, air-drying required (c)

1 ptsCorrected: NoRepeat: No

Equipment and/or utensils are not being air-dried or adequately drained after cleaning and sanitizing them before using them in contact with food.

511-6-1.05(10)(a) - Equipment & Utensils, Air-Drying Required (C) (10) Protection of Clean Items.

(a) Equipment and Utensils, Air-Drying Required. After cleaning and sanitizing, equipment and utensils:

  1. Shall be air-dried or used after adequate draining before contact with food; and

  2. May not be cloth dried except that utensils that have been air-dried may be polished with cloths that are maintained clean and dry.

15A - food and nonfood-contact surfaces cleanable, properly designed, constructed, and used

Regulation: 511-6-1.05(1)(i) - nonfood-contact surfaces (c)

1 ptsCorrected: NoRepeat: No

Observed torn and worn gaskets/seals on both prep top cooler and reach in cooler in poor repair.

511-6-1.05(1)(i) - Nonfood-contact Surfaces (C) (i) Nonfood-contact Surfaces. Nonfood-contact surfaces of equipment that are exposed to splash, spillage, or other food soiling or that require frequent cleaning shall be constructed of a corrosion-resistant, nonabsorbent, and smooth material.

15C - nonfood-contact surfaces clean

Regulation: 511-6-1.05(7)(a)2,3 - equipment, food/nonfood-contact surfaces, and utensils, food-contact surfaces of cooking equipment & nonfood-contact surfaces free of accumulations (c)

1 ptsCorrected: NoRepeat: No

Observed encrusted food debris on reach in cooler and prep top coolers door handles.

511-6-1.05(7)(a)2,3 - Equipment, Food/Nonfood-Contact Surfaces, and Utensils, food-contact surfaces of cooking equipment & nonfood-contact surfaces free of accumulations (C) 2. The food-contact surfaces of cooking equipment and pans shall be kept free of encrusted grease deposits and other soil accumulations.

  1. Nonfood-contact surfaces of equipment shall be kept free of an accumulation of dust, dirt, food residue, and other debris.

15C - nonfood-contact surfaces clean

Regulation: 511-6-1.05(7)(a)2,3 - equipment, food/nonfood-contact surfaces, and utensils, food-contact surfaces of cooking equipment & nonfood-contact surfaces free of accumulations (c)

1 ptsCorrected: NoRepeat: No

Observed soil residue on food storage containers inside the small prep top cooler.

.511-6-1.05(7)(a)2,3 - Equipment, Food/Nonfood-Contact Surfaces, and Utensils, food-contact surfaces of cooking equipment & nonfood-contact surfaces free of accumulations (C) 2. The food-contact surfaces of cooking equipment and pans shall be kept free of encrusted grease deposits and other soil accumulations.

  1. Nonfood-contact surfaces of equipment shall be kept free of an accumulation of dust, dirt, food residue, and other debris.

Apr 11, 2025

Routine

Score: 835 violations

6-1A - proper cold holding temperatures

Regulation: 511-6-1.04(6)(f) - time/temperature control for safety; cold holding (p)

9 ptsCorrected: YesRepeat: No

Observed potentially hazardous food cold held at greater than 41 degrees Fahrenheit.cos: discarded.

4-2B - food-contact surfaces: cleaned & sanitized

Regulation: 511-6-1.05(7)(b) - food contact surfaces and utensils - cleaning frequency (p, c)

4 ptsCorrected: NoRepeat: No

Observed equipment and utensils not washed, rinsed and sanitized at the three-compartment sink.

16B - plumbing installed; proper backflow devices

Regulation: 511-6-1.06(2)(r) - system maintained in good repair (p, c)

2 ptsCorrected: NoRepeat: No

Plumbing system improperly repaired.

14C - single-use/single-service articles: properly stored, used

Regulation: 511-6-1.05(10)(g)(1)&(3) - kitchenware and tableware, single-service/-use items properly handled to protect food-/lip-contact surfaces (c)

1 ptsCorrected: NoRepeat: No

Single use articles and/or single service articles are not being handled, displayed, and/or dispenses so that contamination of food and lip contact surfaces is prevented.

15A - food and nonfood-contact surfaces cleanable, properly designed, constructed, and used

Regulation: 511-6-1.05(3)(j) - sink for washing raw fruit and vegetables (p)

1 ptsCorrected: NoRepeat: No

At least one sink plumbed with hot and cold water under pressure was not provided for the washing of fruits and vegetables. Observed dishwashing at the vegetable prep sink.

Apr 17, 2024

Routine

Score: 952 violations

10D - food properly labeled; original container

Regulation: 511-6-1.04(4)(d) - food storage containers identified with common name of food (c)

3 ptsCorrected: NoRepeat: Yes

Observed squeeze bottles in main kitchen unlabeled. CA: items removed from its original container shall be labeled with common English name.

511-6-1.04(4)(d) - Food Storage Containers Identified with Common Name of Food (C) (d) Food Storage Containers, Identified with Common Name of Food. Except for containers holding food that can be readily and unmistakably recognized, such as dry pasta, working containers holding food or food ingredients that are removed from their original packages for use in the food establishment, such as cooking oils, flour, herbs, potato flakes, salt, spices, and sugar shall be clearly and legibly identified, in English, with the common name of the food.

15C - nonfood-contact surfaces clean

Regulation: 511-6-1.05(7)(a)2,3 - equipment, food/nonfood-contact surfaces, and utensils, food-contact surfaces of cooking equipment & nonfood-contact surfaces free of accumulations (c)

1 ptsCorrected: NoRepeat: No

Observed debris inside of multiple RIC units. CA: nonfood contact surfaces shall be free of accumulation of debris.

511-6-1.05(7)(a)2,3 - Equipment, Food/Nonfood-Contact Surfaces, and Utensils, food-contact surfaces of cooking equipment & nonfood-contact surfaces free of accumulations (C) 2. The food-contact surfaces of cooking equipment and pans shall be kept free of encrusted grease deposits and other soil accumulations.

  1. Nonfood-contact surfaces of equipment shall be kept free of an accumulation of dust, dirt, food residue, and other debris.

Oct 5, 2023

Routine

Score: 922 violations

6-2 - proper date marking and disposition

Regulation: 511-6-1.04(6)(h) - ready-to-eat time/temperature control for safety food, disposition (p)

4 ptsCorrected: NoRepeat: No

Observed combined ready-to-eat potentially hazardous food (sauce mix) held more than 24 hours not date marked according to earliest date of opening/preparation in a reach in cooler. Refrigerated, ready-to-eat, time/temperature control for safety food prepared and held in a food establishment for more than 24 hours shall be clearly marked to indicate the date or day by which the food shall be consumed on the premises, sold, or discarded, when held at a temperature of 41°F (5°C) or below for a maximum of 7 days. The day of preparation shall be counted as Day 1. PIC shall observe proper date marking on an opened/prepared container/package of ready-to-eat potentially hazardous food to indicate opened and discarded date. Once food is held over 24 hours, food must be date mark w/either discard or prepared date. C/A: Items will be labeled.

10D - food properly labeled; original container

Regulation: 511-6-1.04(4)(d) - food storage containers identified with common name of food (c)

3 ptsCorrected: NoRepeat: Yes

Observed all storage food containers were not identified with the common name of the food item. CA: Except for containers holding food that can be readily and unmistakably recognized, such as dry pasta, working containers holding food or food ingredients that are removed from their original packages for use in the food establishment, such as cooking oils, flour, herbs, potato flakes, salt, spices, and sugar shall be clearly and legibly identified, in English, with the common name of the food.