Soul Dam Good

Observed reach in cooler handles, shelves and gaskets soiled with food debris throughout cook line in kitchen. Instructed operator to properly clean and sanitize no food contact surfaces during inspection. Must correct within 10 days. 511-6-1.05(7)(a)2,3 - Equipment, Food/Nonfood-Contact Surfaces, and Utensils, food-contact surfaces of cooking equipment & nonfood-contact surfaces free of accumulations (C) 2. The food-contact surfaces of cooking equipment and pans shall be kept free of encrusted grease deposits and other soil accumulations.

3. Nonfood-contact surfaces of equipment shall be kept free of an accumulation of dust, dirt, food residue, and other debris.

Observed raw shell eggs stored above aluminum container holding tartar sauce and cooked Mac and cheese inside Duckers single door reach in cooler in kitchen. Employee moved tartar sauce and cooked Mac and cheese above raw shell eggs for proper storage during inspection. 511-6-1.04(4)(c)1(i)(ii)(iii)(v)(vi)(vii)(viii) - Packaged & Unpackaged Food Separation, Packaging, and Segregation (P, C) (c) Packaged and Unpackaged Food - Separation, Packaging, and Segregation.

1. Food shall be protected from cross contamination by:

(i) Except as specified in paragraph (i)(IV) of this subsection, separating raw animal foods during storage, preparation, holding, and display.

Observed container holding cooked oxtails without proper date labeled stored on shelf in three door reach in cooler in kitchen. Employee stated oxtails prepared last week Thursday 4/16/26 and container was labeled during inspection. Must discarded cooked prepared foods after 7 days. 511-6-1.04(6)(g) - Ready-To-Eat Time/Temperature Control for Safety Food, Date Marking (Pf) (g) Ready-to-Eat Time/Temperature Control for Safety Food, Date Marking

1. Except when packaging food using a reduced oxygen packaging method, and except as specified in paragraphs 5 and 6 of this subsection, refrigerated, ready-to-eat, time/temperature control for safety food prepared and held in a food establishment for more than 24 hours shall be clearly marked to indicate the date or day by which the food shall be consumed on the premises, sold, or discarded, when held at a temperature of 41°F (5°C) or below for a maximum of 7 days. The day of preparation shall be counted as Day 1. Pf

2. Except as specified in paragraphs 5 through 7 of this subsection, refrigerated, ready-to-eat, time/temperature control for safety food prepared and packaged by a food processing plant shall be clearly marked, at the time the original container is opened in a food service establishment and if the food is held for more than 24 hours, to indicate the date or day by which the food shall be consumed on the premises, sold, or discarded, when held at a temperature of 41°F (5°C) or below for a maximum of 7 days after the original container is opened. The day the original container is opened in the food service establishment shall be counted as Day 1, except, the day or date marked by the food service establishment may not exceed a manufacturer’s use by date if the manufacturer determined the use-by date based on food safety; Pf

3. A refrigerated, ready-to-eat, time/temperature control for safety food ingredient or a portion of a refrigerated, ready-to-eat, time/temperature control for safety food that is subsequently combined with additional ingredients or portions of food shall retain the date marking of the earliest-prepared or first-prepared ingredient. Pf

4. A date marking system that meets the criteria stated in paragraphs 1 and 2 of this subsection may include:

(i) Using a method approved by the Health Authority for refrigerated, ready-to-eat time / temperature control for safety food that is frequently rewrapped, such as lunchmeat or a roast, or for which date marking is impractical, such as soft serve mix or milk in a dispensing machine; (ii) Marking the date or day of preparation, with a procedure to discard the food on or before the last date or day by which the food must be consumed on the premises, sold, or discarded

Observed no hot water pressure coming from hand sink water handle. Must repair handle within 7 days.

511-6-1.06(1)(g),(h) - Water Supply, Capacity; Pressure (Pf) (g) Capacity.

1. The water source and system shall be of sufficient capacity to meet the peak water demands of the food service establishment. Pf

2. Hot water generation and distribution systems shall be sufficient to meet the peak hot water demands throughout the food service establishment. Pf (h) Pressure. Water under pressure shall be provided to all fixtures, equipment, and nonfood equipment that are required to use water except that water supplied as specified under subsection (1)(k)1 and 2 to a temporary food service operation or in response to a temporary interruption of a water supply need not be under pressure. Pf

Observed shelf under prep table rusted in kitchen. 511-6-1.05(1)(i) - Nonfood-contact Surfaces (C) (i) Nonfood-contact Surfaces. Nonfood-contact surfaces of equipment that are exposed to splash, spillage, or other food soiling or that require frequent cleaning shall be constructed of a corrosion-resistant, nonabsorbent, and smooth material.

Observed reach in cooler shelves and gaskets soiled with food debris throughout cook line in kitchen. 511-6-1.05(7)(a)2,3 - Equipment, Food/Nonfood-Contact Surfaces, and Utensils, food-contact surfaces of cooking equipment & nonfood-contact surfaces free of accumulations (C) 2. The food-contact surfaces of cooking equipment and pans shall be kept free of encrusted grease deposits and other soil accumulations.

3. Nonfood-contact surfaces of equipment shall be kept free of an accumulation of dust, dirt, food residue, and other debris.

Observed floor and wall junctures damage along bottom of wall in hallway leading to exit door in kitchen. Operator instructed to repair damaged wall during inspection.

511-6-1.07(2)(a) - Floor, Walls, & Ceilings, Cleanability (C) (2) Design, Construction, and Installation.

(a) Floors, Walls, and Ceilings, Cleanability. Except as specified under subsection (2)(d) of this Rule and except for antislip floor coverings or applications that may be used for safety reasons, floors, floor coverings, walls, wall coverings, and ceilings shall be designed, constructed, and installed so they are smooth and easily cleanable

Observed potentially hazardous food (seafood) thawed in standing water. The is only one prep sink. The prep sink shall be for vegetable only.

Observed raw/undercooked animal foods (raw fish) being prepared/stored in fruit and vegetable sink.

511-6-1.04(4)(g) - Washing Fruits & Vegetables (Pf) (g) Washing Fruits and Vegetables.

1. Except as specified in paragraphs (g)2 and 3 of this subsection and except for whole, raw fruits and vegetables that are intended for washing by the consumer before consumption, raw fruits and vegetables shall be thoroughly washed in water, in a sink designated for that purpose only, to remove soil and other contaminants before being cut, combined with other ingredients, cooked, served, or offered for human consumption in ready-to-eat form.

Observed no hot water pressure coming from hand sink water handle. Must repair handle within 7 days.

511-6-1.06(1)(g),(h) - Water Supply, Capacity; Pressure (Pf) (g) Capacity.

1. The water source and system shall be of sufficient capacity to meet the peak water demands of the food service establishment. Pf

2. Hot water generation and distribution systems shall be sufficient to meet the peak hot water demands throughout the food service establishment. Pf (h) Pressure. Water under pressure shall be provided to all fixtures, equipment, and nonfood equipment that are required to use water except that water supplied as specified under subsection (1)(k)1 and 2 to a temporary food service operation or in response to a temporary interruption of a water supply need not be under pressure. Pf

Observed water leaking from cold water handle into prep sink. Must repair within 7 days

511-6-1.06(2)(r) - System Maintained in Good Repair (P, C) (r) System Maintained in Good Repair. A plumbing system shall be repaired according to law; P and maintained in good repair.

The most current inspection report is not prominently displayed in public view, within 15 feet of the front or primary public door and between five feet and seven feet from the floor or in an area where it can be read at a distance of one foot away.

Nonfood contact surfaces of equipment (shelf under prep table in kitchen) that are exposed to splash, spillage, or other food soiling that require frequent cleaning are not constructed of corrosion resistant, nonabsorbent, and smooth materials (Shelf is rusted out.

511-6-1.05(1)(a) - Materials, General Requirements (P, C) (1) Materials.

(a) General Requirements. Utensils and food-contact surfaces of equipment shall be made of materials that do not allow the migration of deleterious substances or impart colors, odors, or tastes to food and under normal use conditions, and shall be: P safe P, durable, corrosion-resistant, and nonabsorbent. In addition, materials shall be sufficient in weight and thickness to withstand repeated warewashing and shall be finished to have a smooth, easily cleanable surface. Materials shall be resistant to pitting, chipping, crazing, scratching, scoring, distortion and decomposition.

Observed floor and wall junctures missing cove base in prep area along bottom of wall. Must provide within 7 days

511-6-1.07(2)(a) - Floor, Walls, & Ceilings, Cleanability (C) (2) Design, Construction, and Installation.

(a) Floors, Walls, and Ceilings, Cleanability. Except as specified under subsection (2)(d) of this Rule and except for antislip floor coverings or applications that may be used for safety reasons, floors, floor coverings, walls, wall coverings, and ceilings shall be designed, constructed, and installed so they are smooth and easily cleanable

Observed Ceiling not smooth and easily cleanable inside prep area..

Observed improper vertical separation of raw animal foods (Raw chicken stored above seafood and seafood stored above green beans) inside 3 door reach in cooler.

511-6-1.04(4)(c)1(i)(ii)(iii)(v)(vi)(vii)(viii) - Packaged & Unpackaged Food Separation, Packaging, and Segregation (P, C) (c) Packaged and Unpackaged Food - Separation, Packaging, and Segregation.

1. Food shall be protected from cross contamination by:

(i) Except as specified in paragraph (i)(IV) of this subsection, separating raw animal foods during storage, preparation, holding, and display from:

Observed combined ready-to-eat potentially hazardous food he ld more than 24 hours inside reach in cooler on cook line not date marked according to earliest date preparation day. COS All leftover Foods discarded. Violation Code Reference 511-6-1.04(6)(g) - Ready-To-Eat Time/Temperature Control for Safety Food, Date Marking (Pf) (g) Ready-to-Eat Time/Temperature Control for Safety Food, Date Marking

1. Except when packaging food using a reduced oxygen packaging method, and except as specified in paragraphs 5 and 6 of this subsection, refrigerated, ready-to-eat, time/temperature control for safety food prepared and held in a food establishment for more than 24 hours shall be clearly marked to indicate the date or day by which the food shall be consumed on the premises, sold, or discarded, when held at a temperature of 41°F (5°C) or below for a maximum of 7 days. The day of preparation shall be counted as Day 1. Pf

2. Except as specified in paragraphs 5 through 7 of this subsection, refrigerated, ready-to-eat, time/temperature control for safety food prepared and packaged by a food processing plant shall be clearly marked, at the time the original container is opened in a food service establishment and if the food is held for more than 24 hours, to indicate the date or day by which the food shall be consumed on the premises, sold, or discarded, when held at a temperature of 41°F (5°C) or below for a maximum of 7 days after the original container is opened. The day the original container is opened in the food service establishment shall be counted as Day 1, except, the day or date marked by the food service establishment may not exceed a manufacturer’s use by date if the manufacturer determined the use-by date based on food safety; Pf

3. A refrigerated, ready-to-eat, time/temperature control for safety food ingredient or a portion of a refrigerated, ready-to-eat, time/temperature control for safety food that is subsequently combined with additional ingredients or portions of food shall retain the date marking of the earliest-prepared or first-prepared ingredient. Pf

4. A date marking system that meets the criteria stated in paragraphs 1 and 2 of this subsection may include:

(i) Using a method approved by the Health Authority for refrigerated, ready-to-eat time / temperature control for safety food that is frequently rewrapped, such as lunchmeat or a roast, or for which date marking is impractical, such as soft serve mix or milk in a dispensing machine; (ii) Marking the date or day of preparation, with a procedure to discard the food on or before the last date or day by which the food must be consumed on the premises, sold, or discarded

Observed food items in storage containers were not identified with the common name of the food item. (all unidentifiable/unlabeled foods discarded by manager)

Observed outer openings not protected at the bottom of the rear door. Must repair within 10 days.

1. Except as specified in paragraphs 2 through 5 of this subsection, outer openings of a food service establishment shall be protected against the entry of insects and rodents by:

(i) Filling or closing holes and other gaps along floors, walls, and ceilings;

(ii) Closed, tight-fitting windows; and

(iii) Solid, self-closing, tight-fitting doors.

2. The requirements in paragraph 1 of this subsection does not apply if a food service establishment opens into a larger structure, such as a mall, airport, or office building, or into an attached structure, such as a porch, and the outer openings from the larger or attached structure are protected against the entry of insects and rodents.

3. Exterior doors used as exits need not be self-closing if they are:

(i) Solid and tight-fitting;

(ii) Designated for use only when an emergency exists, by the fire protection authority that has jurisdiction over the food establishment; and

(iii) Limited-use so they are not used for entrance or exit from the building for purposes other than the designated emergency exit use.

4. Except as specified in paragraphs 2 and 5 of this subsection, if the windows or doors of a food service establishment, or of a larger structure within which a food service establishment is located, are kept open for ventilation or other purposes or a temporary food service establishment is not provided with windows and doors as specified under paragraph 1 of this subsection, the openings shall be protected against the entry of insects and rodents by:

(i) 16 mesh to 1 inch (16 mesh to 25.4 mm) screens;

(ii) Properly designed and installed air curtains to control flying insects; or

(iii) Other effective means.

5. The requirement in paragraph 4 of this subsection does not apply if flying insects and other pests are absent due to the location of the establishment, the weather, or other limiting condition.

Observed water leaking from hot water handle at prep sink. Must repair within 10 days.

511-6-1.06(2)(r) - System Maintained in Good Repair (P, C) (r) System Maintained in Good Repair. A plumbing system shall be repaired according to law; P and maintained in good repair.

Equipment (household microwave oven) and/or utensils in the establishment are not designed and constructed to be durable to retain their characteristic qualities under normal use conditions.

Reach in chicken cooler without shelves.

Observed Reach-in cooler (in the cooking area) not cleaned to prevent accumulation of soil residue. Also water standing in the bottom of the 3 door reach in cooler in the prep area.

Observed floor and wall junctures (cove base missing) not coved on wall outside the hand sink. Must repair within 10 days

511-6-1.07(2)(c) - Floor and Wall Junctures, Coved, & Enclosed or Sealed, water-flushed floors provided with drains & graded to drain (C) (c) Floor and Wall Junctures, Coved, and Enclosed or Sealed.

1. In food service establishments in which cleaning methods other than water flushing are used for cleaning floors, the floor and wall junctures shall be coved and closed to no larger than one thirty-second inch (1 mm).

2. The floors in food service establishments in which water flush cleaning methods are used shall be provided with drains and be graded to drain, and the floor and wall junctures shall be coved and sealed.

Observed unapproved ceiling tiles. Tiles are not smooth and easily cleanable inside prep area.

Observed damaged wall not smooth and easily cleanable. Walls outside the hand sink. Must repair within 10 days.

Violation Code Reference 511-6-1.07(2)(h) - Walls & Ceilings, Studs, Joists, & Rafters, not exposed to moisture (C) (h) Walls and Ceilings, Studs, Joists, and Rafters. Except for temporary food service establishments, studs, joists, and rafters may not be exposed in areas subject to moisture.

Observed bodily fluid emergency cleanup kit above microwave and countertop, observed boxes of coking oil stored on the floor, observed pans of covered pans and cheese to cook below pans of raw fish, observed raw meat above 41f since around 3:30 at start of inspection, observed prep sink not designated for ready to eat foods only, and observed dishwasher with what appears to be same gloves throughout dishwashing process. CA: Reorganize kitchen so that food and food contact areas will be protected from contamination. Code requires:

(e) Monitoring of Receiving. Employees are visibly observing and verifying delivered foods as they are received to determine that they are from approved sources and are placed into appropriate storage locations, as required by this Chapter, such that they are received and maintained at the required temperatures, protected from contamination, unadulterated, and accurately presented, by routinely monitoring the employees’ observations, maintaining receiving/corrective action records for deliveries during non-operating hours, and periodically evaluating foods upon their receipt as specified within DPH Rule 511-6-1-.04(3)(m);PfP

(h) Proper Cooling Methods. Employees are using proper methods to rapidly cool time/temperature control for safety food, that are not held hot or are not for consumption within four hours, through daily oversight of the employees' routine monitoring of food temperatures during cooling;Pf

(i) Proper Thawing. Food employees are properly maintaining the temperature of Time/Temperature control for safety foods during thawing through daily oversight of the food employee’s routine monitoring of food temperatures;Pf.

(k) Proper Sanitizing. Employees are properly sanitizing cleaned multiuse equipment and utensils before they are reused, through routine monitoring of solution temperature and exposure time for hot water sanitizing, and chemical concentration, pH, temperature, and exposure time for chemical sanitizing;Pf

Corrections made onsite: moved food to correct locations except for dry storage. Need additional shelves. Forwarded food safety information on proper storage, cooling, and thawing procedures.

Observed raw pork chops thawing on drain board of vegetable prep sink with running water over the product flowing down into the sink and down the drain. CA: Do not use raw meat at ready to eat prep sink. Wash, rinse, and sanitize the sink now has been contaminated with the raw meat. Code: 7) Cleaning of Equipment and Utensils. (a) Equipment, Food-Contact Surfaces, and Utensils. 1. Equipment food-contact surfaces and utensils shall be clean to sight and touch. Pf.

Observed raw veal chops in refrigerator for around 3 hours above 41F. CA: Must make sure to cool according to code within 4 hours. Cos: raw veal chops moved from reach in refrigerator to the freezer and achieved 41F prior to inspector's exiting the facility. Code: Cooling Methods (Pf, C) - (e) Cooling Methods.

1. Cooling shall be accomplished in accordance with the time and temperature criteria specified under DPH Rule 511-6-1-.04(6)(d) by using one or more of the following methods depending on the type of food being cooled: (i) Placing the food in shallow pans; Pf (ii) Separating the food into smaller or thinner portions; Pf (iii) Using rapid cooling equipment; Pf (iv) Stirring the food in a container placed in an ice water bath; Pf (v) Using containers that facilitate heat transfer; Pf (vi) Adding ice as an ingredient; Pf or (vii) Other effective methods. Pf
2. When placed in cooling or cold holding equipment, food containers in which food is being cooled shall be: (i) Arranged in the equipment to provide maximum heat transfer through the container walls; and (ii) Loosely covered, or uncovered if protected from overhead contamination during the cooling period to facilitate heat transfer from the surface of the food.

Observed thawed portions of pork chops at 67 degrees f in running water for unknown period of time. COS: Pork chops were placed in the refrigerator to begin the cooling process. CA/Code: Thawed portions of the pork chops shall not exceed 41F for more than four hours including: (I) The time the food is exposed to the running water and the time needed for preparation for cooking PF, or (II) The time it takes under refrigeration to lower the food temperature to 41°F (5°C) PF

Expired permit: The most current permit was not observed posted for public view. CA: Replace old permit once annual fee is paid and new permit is received. Code: Post the permit in a location in the food service establishment that is conspicuous to consumers.

Observed failure to maintain TCS food items at or below 41F Observed reach-in cooler in main kitchen not maintaining proper temperature as noted below in temperature section. Except during preparation, cooking, or cooling, or when time is used as the public health control, time/temperature control for safety food shall be maintained at 41°F (5°C) or below PIC removed old from cooler and discarded

Missing door sweep at back door. Provide for permitting. Code: (m) Outer Openings, Protected.

1. Except as specified in paragraphs 2 through 5 of this subsection, outer openings of a food service establishment shall be protected against the entry of insects and rodents by:

(i) Filling or closing holes and other gaps along floors, walls, and ceilings;

(ii) Closed, tight-fitting windows; and

(iii) Solid, self-closing, tight-fitting doors.

2. The requirements in paragraph 1 of this subsection does not apply if a food service establishment opens into a larger structure, such as a mall, airport, or office building, or into an attached structure, such as a porch, and the outer openings from the larger or attached structure are protected against the entry of insects and rodents.

3. Exterior doors used as exits need not be self-closing if they are:

(i) Solid and tight-fitting;

(ii) Designated for use only when an emergency exists, by the fire protection authority that has jurisdiction over the food establishment; and

(iii) Limited-use so they are not used for entrance or exit from the building for purposes other than the designated emergency exit use.

4. Except as specified in paragraphs 2 and 5 of this subsection, if the windows or doors of a food service establishment, or of a larger structure within which a food service establishment is located, are kept open for ventilation or other purposes or a temporary food service establishment is not provided with windows and doors as specified under paragraph 1 of this subsection, the openings shall be protected against the entry of insects and rodents by:

(i) 16 mesh to 1 inch (16 mesh to 25.4 mm) screens;

(ii) Properly designed and installed air curtains to control flying insects; or

(iii) Other effective means.

5. The requirement in paragraph 4 of this subsection does not apply if flying insects and other pests are absent due to the location of the establishment, the weather, or other limiting condition.

Missing door sweep at back door. Provide for permitting. Code: (m) Outer Openings, Protected.

1. Except as specified in paragraphs 2 through 5 of this subsection, outer openings of a food service establishment shall be protected against the entry of insects and rodents by:

(i) Filling or closing holes and other gaps along floors, walls, and ceilings;

(ii) Closed, tight-fitting windows; and

(iii) Solid, self-closing, tight-fitting doors.

2. The requirements in paragraph 1 of this subsection does not apply if a food service establishment opens into a larger structure, such as a mall, airport, or office building, or into an attached structure, such as a porch, and the outer openings from the larger or attached structure are protected against the entry of insects and rodents.

3. Exterior doors used as exits need not be self-closing if they are:

(i) Solid and tight-fitting;

(ii) Designated for use only when an emergency exists, by the fire protection authority that has jurisdiction over the food establishment; and

(iii) Limited-use so they are not used for entrance or exit from the building for purposes other than the designated emergency exit use.

4. Except as specified in paragraphs 2 and 5 of this subsection, if the windows or doors of a food service establishment, or of a larger structure within which a food service establishment is located, are kept open for ventilation or other purposes or a temporary food service establishment is not provided with windows and doors as specified under paragraph 1 of this subsection, the openings shall be protected against the entry of insects and rodents by:

(i) 16 mesh to 1 inch (16 mesh to 25.4 mm) screens;

(ii) Properly designed and installed air curtains to control flying insects; or

(iii) Other effective means.

5. The requirement in paragraph 4 of this subsection does not apply if flying insects and other pests are absent due to the location of the establishment, the weather, or other limiting condition.

Missing storage shelves for food and single service food contact articles. Provide for permitting. Code: (4) Location and Installation.

(a) Equipment, Clothes Washers and Dryers, and Storage Cabinets, Contamination Prevention.

1. Except as specified in paragraph 2 of this subsection, equipment, a cabinet used for the storage of food, or a cabinet that is used to store cleaned and sanitized equipment, utensils, laundered linens, and single-service and single-use articles may not be located under any source of contamination, including in locker rooms; in toilet rooms; in garbage rooms; in mechanical rooms; under sewer lines; under leaking water lines including leaking automatic fire sprinkler heads or under lines on which water has condensed; or under open stairwells.

2. A storage cabinet used for linens or single-service or single-use articles may be stored in a locker room.

Observed nail holes. Fill in all holes with clear silicon sealant for permitting. Code: 2) Design, Construction, and Installation.

(a) Floors, Walls, and Ceilings, Cleanability. Except as specified under subsection (2)(d) of this Rule and except for antislip floor coverings or applications that may be used for safety reasons, floors, floor coverings, walls, wall coverings, and ceilings shall be designed, constructed, and installed so they are smooth and easily cleanable.

Observed damaged wall where FRP was removed. Repair. Observed coved base coming away from wall. Reattach. Code: (c) Floor and Wall Junctures, Coved, and Enclosed or Sealed.

1. In food service establishments in which cleaning methods other than water flushing are used for cleaning floors, the floor and wall junctures shall be coved and closed to no larger than one thirty-second inch (1 mm).

2. The floors in food service establishments in which water flush cleaning methods are used shall be provided with drains and be graded to drain, and the floor and wall junctures shall be coved and sealed.

Condensation drip from air conditioner vent in kitchen area. Correct drip.