MONKEY 68

Observed several TCS foods were not maintaining temperatures at or below 41F in front service sushi cooler, RIC cooler in kitchen and walk in cooler. PIC Placed the foods in the ice and is advised to maintain temperatures t 41F until the coolers are fixed.

Observed salmon and other fish were not cooling at proper rate. PIC discarded the fish 511-6-1.04(6)(d) - Cooling (P) (d) Cooling.

1. Cooked time/temperature control for safety food shall be cooled:

(i) Within 2 hours from 135°F (57°C) to 70°F (21°C); P and

(ii) Within a total of 6 hours from 135°F (57°C) to 41°F (5°C) or less. P

2. Time/temperature control for safety food shall be cooled within 4 hours to 41°F (5°C) or less if prepared from ingredients at ambient temperature, such as reconstituted foods and canned tuna. P

3. Except as specified under paragraph 4 of this subsection, a time/temperature control for safety food received in compliance with laws allowing a temperature above 41°F (5°C) during shipment from the supplier shall be cooled within 4 hours to 41°F (5°C). P

4. Raw eggs shall be received and immediately placed in refrigerated equipment that maintains an ambient air temperature of 41°F (5°C) or less. P

Observed PIC had no knowledge on how to check temperatures of TCS foods and do not have allergy notice posted in the kitchen. 511-6-1.03(1)(a)-(c)1,4,5,6-14,15, 16 - Demonstration of knowledge (Pf) (1) Demonstration of Knowledge. Based on the risk of foodborne illness inherent to the food service operation, during inspections and upon request, the person in charge shall demonstrate to the Health Authority knowledge of foodborne disease prevention, application of the Hazard Analysis Critical Control Point principles, and the requirements of this Chapter. The person in charge shall demonstrate this knowledge in one of the following ways:

(a) Compliance with Chapter. Complying with this Chapter by having no violations of Priority Items during the current inspection; Pf

(b) Certified Food Service Manager. Being a certified food service manager who has shown proficiency of required information through passing a test that is part of an accredited program; Pf or

(c) Correct Answers to Food Safety Questions. Responding correctly to the inspector's questions as they relate to the specific food operation

Observed hand wash sink in the bar had utensils placed in it and in the sushi serving area is blocked with the rice cooker.PIC cleared the items and was advised to maintain the handwash clear of obstructions. 511-6-1.06(2)(o) - Using a Handwashing Sink- Operation & maintenance (Pf) (o) Using a Handwashing Sink.

1. A handwashing sink shall be maintained so that it is accessible at all times for employee use. Pf

2. A handwashing facility may not be used for purposes other than handwashing. Pf

3. An automatic handwashing facility shall be used in accordance with manufacturer’s instructions. Pf

At the time of inspection, PIC failed to provide thermometer to check the temperature of fish and other TCS foods in the facility.PIC advised to obtain a thermometer ASAP. 511-6-1.05(3)(g) - Food TMD, Provided and Accessible; Appropriate TMD for Measuring Thin Foods (Pf) (g) Food Temperature Measuring Devices.

1. Food temperature measuring devices shall be provided and readily accessible for use in ensuring attainment and maintenance of food temperatures as specified under DPH Rule 511-6-1-.04. Pf

2. A temperature measuring device with a suitable small-diameter probe that is designed to measure the temperature of thin masses shall be provided and readily accessible to accurately measure the temperature in thin foods such as meat patties and fish filets. Pf

At the time of inspection PIC failed to provide undamaged test strips for the 3 compartment sink sanitizer.PIC advised to get them ASAP. 511-6-1.05(3)(h),(i),(j) - Temperature Measuring Device, Manual Warewashing; Sanitizing Solutions, Testing Device (Pf) (h) Temperature Measuring Devices, Manual and Mechanical Warewashing.

1. In manual warewashing operations, a temperature measuring device shall be provided and readily accessible for frequently measuring the washing and sanitizing temperatures. Pf

2. In hot water mechanical warewashing operations, an irreversible registering temperature indicator shall be provided and readily accessible for measuring the utensil surface temperature. Pf

(i) Sanitizing Solutions, Testing Devices. A test kit or other device that accurately measures the concentration in mg/L of sanitizing solutions shall be provided. Pf

Observed handwash sink in main kitchen with knife inside, observed handwash sink in back of kitchen with utensils in it upon arrival. Using a Handwashing Sink.

1. A handwashing sink shall be maintained so that it is accessible at all times for employee use.
2. A handwashing facility may not be used for purposes other than handwashing. C/A COS: PIC removed utensils from sink.