Oakwood, Hall County

CEDARHURST OF OAKWOOD

4251 HUDSON DR OAKWOOD, GA 30566

Food
Latest score
95
May 27, 2026
City
Oakwood
County
Hall
Inspections
6

Score history

Inspection scores over time for this facility.

Inspection history

Georgia inspection history is score-based, with violations grouped under each recorded inspection.

May 27, 2026

Routine

Score: 952 violations

2-2B - proper eating, tasting, drinking, or tobacco use

Regulation: 511-6-1.03(5)(k)1&2 - eating, drinking, or using tobacco (c)

4 ptsCorrected: YesRepeat: No

Observed reusable cup to be stored next to RTE cereal and a Styrofoam cup without a lid or straw to be stored above the ice machine. 511-6-1.03(5)(k)1&2 - Eating, Drinking, or Using Tobacco (C) (k) Hygienic Practices. 2. Employees shall consume food only in approved designated areas separate from food preparation and serving areas, equipment or utensil areas and food storage areas. However, drinking from a single service beverage cup with a secure lid and straw that is handled to prevent contamination of the employee’s hands, the container, exposed food, clean equipment, utensils and linens, unwrapped single-service and single-use articles will be allowed. COS: The drinks were removed by the PIC from food preparation areas.

15A - food and nonfood-contact surfaces cleanable, properly designed, constructed, and used

Regulation: 511-6-1.05(6)(b) - cutting surfaces (c)

1 ptsCorrected: NoRepeat: No

Observed cutting boards underneath the prep table in the middle of the facility to have deep grooves and soil accumulation along with the left prep top cooler cutting board. 511-6-1.05(6)(b) - Cutting Surfaces (C) (b) Cutting Surfaces. Surfaces such as cutting blocks and boards that are subject to scratching and scoring shall be resurfaced if they can no longer be effectively cleaned and sanitized, or discarded if they cannot be resurfaced. Note: The facility will need to have these cutting boards resurfaced or replaced as needed.

Nov 12, 2025

Routine

Score: 922 violations

2-2D - adequate handwashing facilities supplied & accessible

Regulation: 511-6-1.06(2)(o) - using a handwashing sink- operation & maintenance (pf)

4 ptsCorrected: YesRepeat: No

Observed kitchen hand sink to not be accessible at all times for food employees. 511-6-1.06(2)(o) - Using a Handwashing Sink- Operation & maintenance (Pf) (o) Using a Handwashing Sink.

  1. A handwashing sink shall be maintained so that it is accessible at all times for employee use. Pf
  2. A handwashing facility may not be used for purposes other than handwashing. Pf
  3. An automatic handwashing facility shall be used in accordance with manufacturer’s instructions. Pf COS: The PIC immediately cleared the hand sink to allow for easy accessibility for all food employees.

4-2B - food-contact surfaces: cleaned & sanitized

Regulation: 511-6-1.05(6)(n) - manual and mechanical warewashing equipment, chemical sanitization-temperature, ph, concentration, hardness (p,pf)

4 ptsCorrected: YesRepeat: No

Observed low-temperature ware-washing machine to register at 0ppm for chlorine with a chemical chlorine test kit. Liquid pot and pan detergent was actively being used in place of chlorine sanitizer. 511-6-1.05(6)(n) - Manual and Mechanical Warewashing Equipment, Chemical Sanitization-Temperature, pH, Concentration, Hardness (P,Pf) (n) Manual and Mechanical Warewashing Equipment, Chemical Sanitization - Temperature, pH, Concentration, and Hardness. A chemical sanitizer used in a sanitizing solution for a manual or mechanical operation at contact times specified under subsection (8)(b)3 of this Rule shall meet the requirements specified in DPH Rule 511-6-1-.07(6)(g), shall be used in accordance with the Environmental Protection Agency (EPA)-registered label use instructions P, and shall be used as follows:

  1. A chlorine solution shall have a minimum temperature based on the concentration and pH of the solution as listed in the following chart; P

Concentration Range Minimum Temperature

MG/L PH 10 or less oF (oC) PH 8 or less oF (oC)

25-49 120 (49) 120 (49)

50-99 100 (38) 75 (24)

100 55 (13) 55 (13) COS: EHS educated on the importance of ensuring all dishes are properly sanitized, using the mechanical ware-washing machine. The machine was primed with the correct chlorine chemical sanitizer and after running the unit 3 times a chlorine concentration between 50-100ppm was noted.

Dec 18, 2024

Routine

Score: 941 violation

4-2B - food-contact surfaces: cleaned & sanitized

Regulation: 511-6-1.05(6)(n) - manual and mechanical warewashing equipment, chemical sanitization-temperature, ph, concentration, hardness (p,pf)

4 ptsCorrected: NoRepeat: Yes

Ware-wash machine registered 0ppm of Chlorine when measured with a Chemical Test kit. Ware-wash machine chlorine chemical should have a concentration of 50-100ppm when tested (mechanically and manual sanitization). PIC to use the 3-compartment sink to wash, rinse and sanitize all equipment/dishes until the ware-wash machine is repaired to ensure proper sanitization of equipment/dishes.

May 17, 2024

Routine

Score: 834 violations

6-1A - proper cold holding temperatures

Regulation: 511-6-1.04(6)(f) - time/temperature control for safety; cold holding (p)

9 ptsCorrected: YesRepeat: No

Various TCS food items (Please see temperature log) were observed cold holding at temperatures above 41 Degrees Fahrenheit. 511-6-1.04(6)(f) - Time/Temperature Control for Safety; Cold Holding (P) (f) Time/Temperature Control for Safety Food, Hot and Cold Holding. Except during preparation, cooking, or cooling, or when time is used as the public health control, time/temperature control for safety food shall be maintained at 41°F (5°C) or below or 135°F (57°C) or above, except that roasts cooked to a temperature and for a time specified in subsection (5)(a)2 of this Rule and reheated using the same temperature and time conditions as cooking may be held at a temperature of 130°F (54°C) or above. P Note: All the TCS food items were voluntarily discarded during the inspection.

4-2B - food-contact surfaces: cleaned & sanitized

Regulation: 511-6-1.05(6)(n) - manual and mechanical warewashing equipment, chemical sanitization-temperature, ph, concentration, hardness (p,pf)

4 ptsCorrected: NoRepeat: No

The dish washing machine registerd 0ppm of Chlorine when measured with a Chemical Test kit. 511-6-1.05(6)(n) - Manual and Mechanical Warewashing Equipment, Chemical Sanitization-Temperature, pH, Concentration, Hardness (P,Pf) (n) Manual and Mechanical Warewashing Equipment, Chemical Sanitization - Temperature, pH, Concentration, and Hardness. A chemical sanitizer used in a sanitizing solution for a manual or mechanical operation at contact times specified under subsection (8)(b)3 of this Rule shall meet the requirements specified in DPH Rule 511-6-1-.07(6)(g), shall be used in accordance with the Environmental Protection Agency (EPA)-registered label use instructions P, and shall be used as follows:

  1. A chlorine solution shall have a minimum temperature based on the concentration and pH of the solution as listed in the following chart; P

Concentration Range Minimum Temperature

MG/L PH 10 or less oF (oC) PH 8 or less oF (oC)

25-49 120 (49) 120 (49)

50-99 100 (38) 75 (24)

100 55 (13) 55 (13)

  1. An iodine solution shall have a minimum temperature of 68°F (20°C)P minimum concentration between 12.5 ppm and 25 ppm, P and pH of 5.0 or less or a pH no higher than the level for which the manufacturer specifies for the solution to be effective; P

  2. A quaternary ammonium compound solution shall have a minimum temperature of 75ºF (24ºC), P have a concentration as specified in DPH Rule 511-6-1-.07(6)(g) and as indicated by the manufacturer’s use directions included in the labeling, P and be used only in water with 500 ppm hardness or less or in water having a hardness no greater than specified by the EPA-registered label use instructions; P

  3. If another solution of a chemical specified under paragraphs 1 through 3 of this subsection is used, the permit holder shall demonstrate to the Health Authority that the solution achieves sanitization and the use of the solution shall be approved; P

  4. If a chemical sanitizer other than chlorine, iodine, or a quaternary ammonium compound is used, it shall be applied in accordance with the EPA-registered label use instructions Note: The Manager will use the (3) compartment sink to wash rinse and sanitize all equipment until the dishmachine is repaired.

4-2B - food-contact surfaces: cleaned & sanitized

Regulation: 511-6-1.05(7)(a)1 - equipment, food-contact surfaces,& utensils (pf)

4 ptsCorrected: NoRepeat: No

Accumulated food debris was observed on the Electric Multi -use slicer. 511-6-1.05(7)(a)1 - Equipment, Food-Contact Surfaces,& Utensils (Pf) (7) Cleaning of Equipment and Utensils.

(a) Equipment, Food-Contact Surfaces, and Utensils.

  1. Equipment food-contact surfaces and utensils shall be clean to sight and touch. Pf.

6-2 - proper date marking and disposition

Regulation: 511-6-1.04(6)(g) - ready-to-eat time/temperature control for safety food, date marking (pf)

4 ptsCorrected: YesRepeat: No

A bowl of Brown Gravy was observed in the reach in refrigeration unit with no Food date marking. Nobody knew when the gravy was cooked. 511-6-1.04(6)(g) - Ready-To-Eat Time/Temperature Control for Safety Food, Date Marking (Pf) (g) Ready-to-Eat Time/Temperature Control for Safety Food, Date Marking

  1. Except when packaging food using a reduced oxygen packaging method, and except as specified in paragraphs 4 and 5 of this subsection, refrigerated, ready-to-eat, time/temperature control for safety food prepared and held in a food establishment for more than 24 hours shall be clearly marked to indicate the date or day by which the food shall be consumed on the premises, sold, or discarded, when held at a temperature of 41°F (5°C) or below for a maximum of 7 days. The day of preparation shall be counted as Day 1. Pf

  2. Except as specified in paragraphs 4 through 6 of this subsection, refrigerated, ready-to-eat, time/temperature control for safety food prepared and packaged by a food processing plant shall be clearly marked, at the time the original container is opened in a food service establishment and if the food is held for more than 24 hours, to indicate the date or day by which the food shall be consumed on the premises, sold, or discarded, when held at a temperature of 41°F (5°C) or below for a maximum of 7 days after the original container is opened. The day the original container is opened in the food service establishment shall be counted as Day 1, except, the day or date marked by the food service establishment may not exceed a manufacturer’s use by date if the manufacturer determined the use-by date based on food safety; Pf

  3. A refrigerated, ready-to-eat, time/temperature control for safety food ingredient or a portion of a refrigerated, ready-to-eat, time/temperature control for safety food that is subsequently combined with additional ingredients or portions of food shall retain the date marking of the earliest-prepared or first-prepared ingredient. Pf

  4. A date marking system that meets the criteria stated in paragraphs 1 and 2 of this subsection may include:

(i) Using a method approved by the Health Authority for refrigerated, ready-to-eat time / temperature control for safety food that is frequently rewrapped, such as lunchmeat or a roast, or for which date marking is impractical, such as soft serve mix or milk in a dispensing machine;

(ii) Marking the date or day of preparation, with a procedure to discard the food on or before the last date or day by which the food must be consumed on the premises, sold, or discarded;

(iii) Marking the date or day the original container is opened in a food service establishment, with a procedure to discard the food on or before the last date or day by which the food must be consumed on the premises, sold, or discarded; or

(iv) Using calendar dates, days of the week, color-coded marks, or other effective marking methods, provided that the marking system is disclosed to the Health Authority upon request.

  1. The requirements in paragraphs 1 and 2 of this subsection do not apply to individual meal portions served or repackaged for sale from a bulk container upon a consumer’s request.

  2. The requirements in paragraphs 1 and 2 of this subsection do not apply to shellstock.

  3. The requirement in paragraph 2 of this subsection does not apply to the following foods prepared and packaged by a food processing plant inspected by a Health Authority:

(i) Deli salads, such as ham salad, seafood salad, chicken salad, egg salad, pasta salad, potato salad, and macaroni salad, manufactured in accordance with 21 CFR 110 Current good manufacturing practice in manufacturing, packing, or holding human food;

(ii) Hard cheeses containing not more than 39% moisture as defined in 21 CFR 133 Cheeses and related cheese products, such as cheddar, gruyere, parmesan and reggiano, and romano;

(iii) Semi-soft cheeses containing more than 39% moisture, but not more than 50% moisture, as defined in 21 CFR 133 Cheeses and related cheese products, such as blue, edam, gorgonzola, gouda, and monterey jack;

(iv) Cultured dairy products as defined in 21 CFR 131 Milk and cream, such as yogurt, sour cream, and buttermilk;

(v) Preserved fish products, such as pickled herring and dried or salted cod, and other acidified fish products defined in 21 CFR 114 Acidified foods;

(vi) Shelf stable, dry fermented sausages, such as pepperoni and Genoa salami; and

(vii) Shelf stable salt-cured products, such as prosciutto and Parma ham. Note: The brown gravy was voluntarily discarded during the inspection.

Nov 30, 2023

Routine

Score: 972 violations

12B - personal cleanliness

Regulation: 511-6-1.03(5)(g) - jewelry (c)

3 ptsCorrected: YesRepeat: No

Observed an employee wearing a watch, bracelet and ring, while actively preparing food. Except for a plain ring such as a wedding band food employees may not wear jewelry including medical information jewelry on their arms and hands while preparing food. COS: Employee voluntarily removed bracelet, watch and ring during inspection.

12B - personal cleanliness

Regulation: 511-6-1.03(5)(j) - hair restraints (c)

3 ptsCorrected: YesRepeat: No

Observed employee with no form of hair restraint on, while actively preparing food. Employees preparing or handling food shall use effective and clean, disposable or easily cleanable nets or other hair restraints approved by the Health Authority, worn properly to restrain loose hair including beards and mustaches longer than one half inch. COS: Employee voluntarily put on a hat during the inspection.

May 17, 2023

Routine

Score: 952 violations

1-2B - certified food protection manager

Regulation: 511-6-1.03(3)(c) - certification documentation (pf)

4 ptsCorrected: NoRepeat: No

Observed facility without updated and current CFSM certificate. Within ninety days of the expiration of the CFSM certificate, the CFSM shall enroll in an approved food safety training course, pass an approved exam and obtain a new certificate. Note: Kitchen manager is currently enrolled in ServSafe class online.

15B - warewashing facilities: installed, maintained, used; test strips

Regulation: 511-6-1.05(3)(h),(i),(j) - temperature measuring device, manual warewashing; sanitizing solutions, testing device (pf)

1 ptsCorrected: NoRepeat: No

Observed facility without QAC test strips. Sanitizing Solutions, Testing Devices. A test kit or other device that accurately measures the concentration in mg/L of sanitizing solutions shall be provided. Pf Note: PIC will order QAC test strips.