Hamburger Mike's

Observed multiple TCS food items, in main kitchen and front service reach-in coolers above 41F. PIC placed items on ice. 511-6-1.04(6)(f) - Time/Temperature Control for Safety; Cold Holding (P) (f) Time/Temperature Control for Safety Food, Hot and Cold Holding. Except during preparation, cooking, or cooling, or when time is used as the public health control, time/temperature control for safety food shall be maintained at 41°F (5°C) or below or 135°F (57°C) or above, except that roasts cooked to a temperature and for a time specified in subsection (5)(a)2 of this Rule and reheated using the same temperature and time conditions as cooking may be held at a temperature of 130°F (54°C) or above. P

Observed accumulation on ice chute door at self service drink machine. PIC was advised to increase to cleanings to weekly. 511-6-1.05(7)(b) - Food Contact Surfaces and Utensils - Cleaning Frequency (P, C) (b) Equipment Food-Contact Surfaces and Utensils.

1. Equipment food-contact surfaces and utensils shall be cleaned:

(i) Before each use with a different type of raw animal food such as beef, fish, lamb, pork, or poultry. It does not apply if the food-contact surface or utensil is in contact with a succession of different types of raw meat and raw poultry each requiring a higher cooking temperature as specified under DPH Rule 511-6-1.04(5)(a) than the previous type such as preparing raw pork followed by cutting raw poultry on the same cutting board; P

(ii) Each time there is a change from working with raw foods to working with ready-to-eat foods; P

(iii) Between uses with raw fruits and vegetables and with Time/Temperature Control for safety food; P

(iv) Before using or storing a food temperature measuring device; P and

(v) At any time during the operation when contamination may have occurred. P

2. Except as specified in paragraph 3 of this subsection, if used with time/temperature control for safety food, equipment food-contact surfaces and utensils shall be cleaned at least every 4 hours throughout the day. P

3. Surfaces of utensils and equipment contacting time/temperature control for safety food may be cleaned less frequently than every 4 hours if:

(i) In storage, containers of time/temperature control for safety food and their contents are maintained at temperatures specified under DPH Rule 511-6-1-.04 and the containers are cleaned when they are empty;

(ii) Utensils and equipment are used to prepare food in a refrigerated room or area that is maintained at one of the temperatures in the following chart and:

(I) The utensils and equipment are cleaned at the frequency in the following chart that corresponds to the temperature:

Temperature Cleaning Frequency

41ºF (5.0ºC) or less 24 hours

41ºF - 45ºF (>5.0ºC - 7.2ºC) 20 hours

45ºF - 50ºF (>7.2ºC - 10.0ºC) 16 hours

50ºF - 55ºF (>10.0ºC - 12.8ºC) 10 hours

and

(II) The cleaning frequency based on the ambient temperature of the refrigerated room or area is documented in the food service establishment.

(iii) Temperature measuring devices are maintained in contact with food, such as when left in a container of deli food or in a roast, held at temperatures specified under DPH Rule 511-6-1- .04;

(iv) Equipment is used for storage of packaged or unpackaged food, such as a reach-in refrigerator, and the equipment is cleaned at a frequency necessary to preclude accumulation of soil residues;

(v) The cleaning schedule is approved based on consideration of:

(I) Characteristics of the equipment and its use,

(II) The type of food involved,

(III) The amount of food residue accumulation, and

(IV) The temperature at which the food is maintained during the operation and the potential for the rapid and progressive multiplication of pathogenic or toxigenic microorganisms that are capable of causing foodborne disease; or

(vi) In-use utensils are intermittently stored in a container of water in which the water is maintained at 135ºF (57ºC) or more and the utensils and container are cleaned at least every 24 hours or at a frequency necessary to preclude accumulation of soil residues.

4. Dining counters and table-tops shall be cleaned and sanitized routinely after removing all soiled tableware and food trays shall be cleaned and sanitized after each use by one of the following methods:

(i) A two step method in which one cloth, rinsed in sanitizing solution is used to clean food debris from the surface and a second cloth in separate sanitizing solution is used to rinse;

(ii) Sanitizing solution is sprayed onto the surface and the surface is then wiped clean with a disposable towel;

(iii) If used for cleaning and sanitizing, single-use disposable sanitizer wipes shall be used in accordance with EPA-registered label use instructions; or

(iv) Other methods approved by the Health Authority.

(v) Food trays may be cleaned and sanitized the same as table ware.

5. Except when dry cleaning methods are used as specified under subsection (7)(e) of this Rule, surfaces of utensils and equipment contacting food that is not time/temperature control for safety food shall be cleaned:

(i) At any time when contamination may have occurred;

(ii) At least every 24 hours for iced tea dispensers including nozzles and consumer self-service utensils such as tongs, scoops, or ladles;

(iii) Before restocking consumer self-service equipment and utensils such as condiment dispensers and display containers; and

(iv) In equipment such as ice bins and beverage dispensing nozzles and enclosed components of equipment such as ice makers, cooking oil storage tanks and distribution lines, beverage and syrup dispensing lines or tubes, coffee bean grinders, and water vending equipment:

(I) At a frequency specified by the manufacturer; or

(II) Absent manufacturer specifications, at a frequency necessary to preclude accumulation of soil or mold.

Observed expired quaternary ammonium sanitizer test strips within facility. 511-6-1.05(6)(p) - Warewashing Equipment, Determining Chemical Sanitizer Concentration (Pf) (p) Warewashing Equipment, Determining Chemical Sanitizer Concentration. Concentration of the sanitizing solution shall be accurately determined by using a test kit or other device. Pf.

Observed excessive black mold-like accumulation in drink machine ice chute interior and pink accumulation on ice chute door. 511-6-1.05(7)(b) - Food Contact Surfaces and Utensils - Cleaning Frequency (P, C) (b) Equipment Food-Contact Surfaces and Utensils.

1. Equipment food-contact surfaces and utensils shall be cleaned:

(i) Before each use with a different type of raw animal food such as beef, fish, lamb, pork, or poultry. It does not apply if the food-contact surface or utensil is in contact with a succession of different types of raw meat and raw poultry each requiring a higher cooking temperature as specified under DPH Rule 511-6-1.04(5)(a) than the previous type such as preparing raw pork followed by cutting raw poultry on the same cutting board; P

(ii) Each time there is a change from working with raw foods to working with ready-to-eat foods; P

(iii) Between uses with raw fruits and vegetables and with Time/Temperature Control for safety food; P

(iv) Before using or storing a food temperature measuring device; P and

(v) At any time during the operation when contamination may have occurred. P

2. Except as specified in paragraph 3 of this subsection, if used with time/temperature control for safety food, equipment food-contact surfaces and utensils shall be cleaned at least every 4 hours throughout the day. P

3. Surfaces of utensils and equipment contacting time/temperature control for safety food may be cleaned less frequently than every 4 hours if:

(i) In storage, containers of time/temperature control for safety food and their contents are maintained at temperatures specified under DPH Rule 511-6-1-.04 and the containers are cleaned when they are empty;

(ii) Utensils and equipment are used to prepare food in a refrigerated room or area that is maintained at one of the temperatures in the following chart and:

(I) The utensils and equipment are cleaned at the frequency in the following chart that corresponds to the temperature:

Temperature Cleaning Frequency

41ºF (5.0ºC) or less 24 hours

41ºF - 45ºF (>5.0ºC - 7.2ºC) 20 hours

45ºF - 50ºF (>7.2ºC - 10.0ºC) 16 hours

50ºF - 55ºF (>10.0ºC - 12.8ºC) 10 hours

and

(II) The cleaning frequency based on the ambient temperature of the refrigerated room or area is documented in the food service establishment.

(iii) Temperature measuring devices are maintained in contact with food, such as when left in a container of deli food or in a roast, held at temperatures specified under DPH Rule 511-6-1- .04;

(iv) Equipment is used for storage of packaged or unpackaged food, such as a reach-in refrigerator, and the equipment is cleaned at a frequency necessary to preclude accumulation of soil residues;

(v) The cleaning schedule is approved based on consideration of:

(I) Characteristics of the equipment and its use,

(II) The type of food involved,

(III) The amount of food residue accumulation, and

(IV) The temperature at which the food is maintained during the operation and the potential for the rapid and progressive multiplication of pathogenic or toxigenic microorganisms that are capable of causing foodborne disease; or

(vi) In-use utensils are intermittently stored in a container of water in which the water is maintained at 135ºF (57ºC) or more and the utensils and container are cleaned at least every 24 hours or at a frequency necessary to preclude accumulation of soil residues.

4. Dining counters and table-tops shall be cleaned and sanitized routinely after removing all soiled tableware and food trays shall be cleaned and sanitized after each use by one of the following methods:

(i) A two step method in which one cloth, rinsed in sanitizing solution is used to clean food debris from the surface and a second cloth in separate sanitizing solution is used to rinse;

(ii) Sanitizing solution is sprayed onto the surface and the surface is then wiped clean with a disposable towel;

(iii) If used for cleaning and sanitizing, single-use disposable sanitizer wipes shall be used in accordance with EPA-registered label use instructions; or

(iv) Other methods approved by the Health Authority.

(v) Food trays may be cleaned and sanitized the same as table ware.

5. Except when dry cleaning methods are used as specified under subsection (7)(e) of this Rule, surfaces of utensils and equipment contacting food that is not time/temperature control for safety food shall be cleaned:

(i) At any time when contamination may have occurred;

(ii) At least every 24 hours for iced tea dispensers including nozzles and consumer self-service utensils such as tongs, scoops, or ladles;

(iii) Before restocking consumer self-service equipment and utensils such as condiment dispensers and display containers; and

(iv) In equipment such as ice bins and beverage dispensing nozzles and enclosed components of equipment such as ice makers, cooking oil storage tanks and distribution lines, beverage and syrup dispensing lines or tubes, coffee bean grinders, and water vending equipment:

(I) At a frequency specified by the manufacturer; or

(II) Absent manufacturer specifications, at a frequency necessary to preclude accumulation of soil or mold.

Observed reach-in freezer, next to reach in cooler, door extremely loose and gaskets of reach-in door in disrepair. 511-6-1.05(6)(q)1&3 - Good Repair & Calibration (C) (q) Good Repair and Calibration.

1. Utensils shall be maintained in a state of repair or condition that complies with the requirements specified under subsections (1) and (2) of this Rule or shall be discarded.
2. Ambient air temperature, water pressure, and water temperature measuring devices shall be maintained in good repair and be accurate within the intended range of use.

Observed mold-like accumulation on unsealed wood bar above 3-compartment sink.511-6-1.05(1)(i) - Nonfood-contact Surfaces (C) (i) Nonfood-contact Surfaces. Nonfood-contact surfaces of equipment that are exposed to splash, spillage, or other food soiling or that require frequent cleaning shall be constructed of a corrosion-resistant, nonabsorbent, and smooth material.

Observed food and grease accumulation on bread rack next to prep-top cooler, mold-like accumulation on upper portion and caulking of 3-comartment sink, and food debris in interior of cookie oven. Also observed food debris accumulation in reach-in freezer. 511-6-1.05(7)(a)2,3 - Equipment, Food/Nonfood-Contact Surfaces, and Utensils, food-contact surfaces of cooking equipment & nonfood-contact surfaces free of accumulations (C) 2. The food-contact surfaces of cooking equipment and pans shall be kept free of encrusted grease deposits and other soil accumulations.

3. Nonfood-contact surfaces of equipment shall be kept free of an accumulation of dust, dirt, food residue, and other debris.

Observed ceiling tiles with holes/ in disrepair and wall adjacent to 3-comaprtment sink with mold-like accumulation. Also observed acoustic ceiling tiles in main kitchen area. 11-6-1.07(5)(a),(b) - Good Repair, physical facilities maintained; Cleaning, Frequency & Restrictions, cleaned often enough to keep them clean (C) (5) Maintenance and Operation.

(a) Good Repair. All physical facilities shall be maintained in good repair.

(b) Cleaning, Frequency and Restrictions.

1. The physical facilities shall be cleaned as often as necessary to keep them clean and by methods that prevent contamination of food products.

2. Except for cleaning that is necessary due to a spill or other accident, cleaning shall be done during periods when the least amount of food is exposed, such as after closing.

3. If present, playground equipment and associated areas shall be maintained in a clean and sanitary condition. In addition, a cleaning and sanitizing plan along with cleaning and sanitizing records for playground equipment and associated areas shall be maintained within the food service establishment for review upon request by the Health Authority. Further, such cleaning and sanitizing plan for employees to follow in the event of encountering vomitus or fecal matter shall be included and submitted at the time of permit application as specified in DPH Rule 511-6-1-.02(1)(c). Pf

Observed excessive dust accumulation on vent in restroom. 511-6-1.07(2)(j) - Heating, Ventilation, Air Conditioning, System Vents, designed to prevent contamination (C) (j) Heating, Ventilating, Air Conditioning, System Vents. Heating, ventilating, and air conditioning systems shall be designed and installed so that make-up air intake and exhaust vents do not cause contamination of food, food-contact surfaces, equipment, or utensils.

Observed accumulation on ice chute door in front service drink machine. 511-6-1.05(7)(b) - Food Contact Surfaces and Utensils - Cleaning Frequency (P, C) (b) Equipment Food-Contact Surfaces and Utensils.

1. Equipment food-contact surfaces and utensils shall be cleaned:

(i) Before each use with a different type of raw animal food such as beef, fish, lamb, pork, or poultry. It does not apply if the food-contact surface or utensil is in contact with a succession of different types of raw meat and raw poultry each requiring a higher cooking temperature as specified under DPH Rule 511-6-1.04(5)(a) than the previous type such as preparing raw pork followed by cutting raw poultry on the same cutting board; P

(ii) Each time there is a change from working with raw foods to working with ready-to-eat foods; P

(iii) Between uses with raw fruits and vegetables and with Time/Temperature Control for safety food; P

(iv) Before using or storing a food temperature measuring device; P and

(v) At any time during the operation when contamination may have occurred. P

2. Except as specified in paragraph 3 of this subsection, if used with time/temperature control for safety food, equipment food-contact surfaces and utensils shall be cleaned at least every 4 hours throughout the day. P

3. Surfaces of utensils and equipment contacting time/temperature control for safety food may be cleaned less frequently than every 4 hours if:

(i) In storage, containers of time/temperature control for safety food and their contents are maintained at temperatures specified under DPH Rule 511-6-1-.04 and the containers are cleaned when they are empty;

(ii) Utensils and equipment are used to prepare food in a refrigerated room or area that is maintained at one of the temperatures in the following chart and:

(I) The utensils and equipment are cleaned at the frequency in the following chart that corresponds to the temperature:

Temperature Cleaning Frequency

41ºF (5.0ºC) or less 24 hours

41ºF - 45ºF (>5.0ºC - 7.2ºC) 20 hours

45ºF - 50ºF (>7.2ºC - 10.0ºC) 16 hours

50ºF - 55ºF (>10.0ºC - 12.8ºC) 10 hours

and

(II) The cleaning frequency based on the ambient temperature of the refrigerated room or area is documented in the food service establishment.

(iii) Temperature measuring devices are maintained in contact with food, such as when left in a container of deli food or in a roast, held at temperatures specified under DPH Rule 511-6-1- .04;

(iv) Equipment is used for storage of packaged or unpackaged food, such as a reach-in refrigerator, and the equipment is cleaned at a frequency necessary to preclude accumulation of soil residues;

(v) The cleaning schedule is approved based on consideration of:

(I) Characteristics of the equipment and its use,

(II) The type of food involved,

(III) The amount of food residue accumulation, and

(IV) The temperature at which the food is maintained during the operation and the potential for the rapid and progressive multiplication of pathogenic or toxigenic microorganisms that are capable of causing foodborne disease; or

(vi) In-use utensils are intermittently stored in a container of water in which the water is maintained at 135ºF (57ºC) or more and the utensils and container are cleaned at least every 24 hours or at a frequency necessary to preclude accumulation of soil residues.

4. Dining counters and table-tops shall be cleaned and sanitized routinely after removing all soiled tableware and food trays shall be cleaned and sanitized after each use by one of the following methods:

(i) A two step method in which one cloth, rinsed in sanitizing solution is used to clean food debris from the surface and a second cloth in separate sanitizing solution is used to rinse;

(ii) Sanitizing solution is sprayed onto the surface and the surface is then wiped clean with a disposable towel;

(iii) If used for cleaning and sanitizing, single-use disposable sanitizer wipes shall be used in accordance with EPA-registered label use instructions; or

(iv) Other methods approved by the Health Authority.

(v) Food trays may be cleaned and sanitized the same as table ware.

5. Except when dry cleaning methods are used as specified under subsection (7)(e) of this Rule, surfaces of utensils and equipment contacting food that is not time/temperature control for safety food shall be cleaned:

(i) At any time when contamination may have occurred;

(ii) At least every 24 hours for iced tea dispensers including nozzles and consumer self-service utensils such as tongs, scoops, or ladles;

(iii) Before restocking consumer self-service equipment and utensils such as condiment dispensers and display containers; and

(iv) In equipment such as ice bins and beverage dispensing nozzles and enclosed components of equipment such as ice makers, cooking oil storage tanks and distribution lines, beverage and syrup dispensing lines or tubes, coffee bean grinders, and water vending equipment:

(I) At a frequency specified by the manufacturer; or

(II) Absent manufacturer specifications, at a frequency necessary to preclude accumulation of soil or mold.

Observed leaking dish machine and faucet in unisex restroom. Also observed evidence of refrigeration unit in reach-in freezer leaking. 511-6-1.06(2)(r) - System Maintained in Good Repair (P, C) (r) System Maintained in Good Repair. A plumbing system shall be repaired according to law; P and maintained in good repair.

Observed reach-in freezer unit with evidence of leaking. 511-6-1.05(6)(q)1&3 - Good Repair & Calibration (C) (q) Good Repair and Calibration.

1. Utensils shall be maintained in a state of repair or condition that complies with the requirements specified under subsections (1) and (2) of this Rule or shall be discarded.
2. Ambient air temperature, water pressure, and water temperature measuring devices shall be maintained in good repair and be accurate within the intended range of use.

Observed interior of prep-top cooler in main kitchen area in need of cleaning. Also observed excessive grease accumulation on area between the grill and drawers, with grease on top of drawer frame. 511-6-1.05(7)(a)2,3 - Equipment, Food/Nonfood-Contact Surfaces, and Utensils, food-contact surfaces of cooking equipment & nonfood-contact surfaces free of accumulations (C) 2. The food-contact surfaces of cooking equipment and pans shall be kept free of encrusted grease deposits and other soil accumulations.

3. Nonfood-contact surfaces of equipment shall be kept free of an accumulation of dust, dirt, food residue, and other debris.

Observed multiple food items- beef lettuce, Coleslaw, and burger lettuce- in the reach-in cooler of the main kitchen above 41F. PIC was advised to move items to other reach-in coolers and freezers.

Observed pink and brown accumulation on ice machine deflector. PIC was advised to clean machine bi-weekly.

Observed hot water in employee restroom at 71F and 72F in employee restroom.

Observed debris on interior portion of the soda fountain nozzles. Clean soda nozzles nightly to prevent build up.

Observed no hot water in the restrooms. Hot water must be available in all restrooms and must be at least 85F.

Observed knives stored in between prep top cooler door. Manager removed knives (COS). Utensils should be stored to prevent contamination.

Observed the bottom of the reach in freezer when food debris at the bottom. Observed food build up on reach in freezer in the main kitchen area. All non-food contact surfaces must be clean and free of accumulation.

Observed multiple food items cold held above 41F in the reach-in cooler in the main kitchen. PIC adjusted RIC temperature from 41F to 35F.

Observed mold in the interior of the ice machine in the main kitchen & ice chute interior of the drink fountain machine in the dining area.

Observed mold and grime on the exterior of the reach-in cooler doors.