Marco's Pizza

Observed 3-compartment sink with quaternary ammonium sanitizer solution greater than 400 ppm. Employee began to add more water to dilute the solution. 511-6-1.05(6)(n) - Manual and Mechanical Warewashing Equipment, Chemical Sanitization-Temperature, pH, Concentration, Hardness (P,Pf) (n) Manual and Mechanical Warewashing Equipment, Chemical Sanitization - Temperature, pH, Concentration, and Hardness. A chemical sanitizer used in a sanitizing solution for a manual or mechanical operation at contact times specified under subsection (8)(b)3 of this Rule shall meet the requirements specified in DPH Rule 511-6-1-.07(6)(g), shall be used in accordance with the Environmental Protection Agency (EPA)-registered label use instructions P, and shall be used as follows:

1. A chlorine solution shall have a minimum temperature based on the concentration and pH of the solution as listed in the following chart; P

Concentration Range Minimum Temperature

MG/L PH 10 or less oF (oC) PH 8 or less oF (oC)

25-49 120 (49) 120 (49)

50-99 100 (38) 75 (24)

100 55 (13) 55 (13)

2. An iodine solution shall have a minimum temperature of 68°F (20°C)P minimum concentration between 12.5 ppm and 25 ppm, P and pH of 5.0 or less or a pH no higher than the level for which the manufacturer specifies for the solution to be effective; P

3. A quaternary ammonium compound solution shall have a minimum temperature of 75ºF (24ºC), P have a concentration as specified in DPH Rule 511-6-1-.07(6)(g) and as indicated by the manufacturer’s use directions included in the labeling, P and be used only in water with 500 ppm hardness or less or in water having a hardness no greater than specified by the EPA-registered label use instructions; P

4. If another solution of a chemical specified under paragraphs 1 through 3 of this subsection is used, the permit holder shall demonstrate to the Health Authority that the solution achieves sanitization and the use of the solution shall be approved; P

5. If a chemical sanitizer other than chlorine, iodine, or a quaternary ammonium compound is used, it shall be applied in accordance with the EPA-registered label use instructions ;P and

6. If a chemical sanitizer is generated by a device located on-site at the food service establishment, it shall be used as specified in 1-5 of this subsection and shall be produced by a device that:

(i) complies with law as specified in sections 2(q)(1) and 12 of the Federal Insecticide, Fungicide, and Rodenticide Act (FIFRA), P

(ii) complies with 40 CFR 152.500 Requirement for Devices and 40 CFR 156.10 Labeling Requirements, P

(iii) displays the EPA device manufacturing facility registration number on the device, Pf and

(iv) is operated and maintained in accordance with manufacturer’s instructions. Pf.

7. On-site chemical sanitizer generating equipment with active ingredients, such as copper, must be registered as pesticides. The active ingredient may be part of the equipment or separately added.

Observed leaking around men's restroom faucet. 511-6-1.06(2)(r) - System Maintained in Good Repair (P, C) (r) System Maintained in Good Repair. A plumbing system shall be repaired according to law; P and maintained in good repair.

Observed floors in walk-in cooler in need of resealing and walk-in cooler door not properly closing. 511-6-1.05(6)(a) - Good Repair & Proper Adjustment (C) (6) Maintenance and Operation.

(a) Good Repair and Proper Adjustment.

1. Equipment shall be maintained in a state of repair and condition that meets the requirements specified under subsections (1) and (2)of this Rule.

2. Equipment components such as doors, seals, hinges, fasteners, and kick plates shall be kept intact, tight, and adjusted in accordance with manufacturer's specifications.

3. Cutting or piercing parts of can openers shall be kept sharp to minimize the creation of metal fragments that can contaminate food when the container is opened.

Observed rust and debris accumulation on shelving in walk-in cooler, and chipping paint and rust accumulation on reach-in cooler shelving. 511-6-1.05(7)(d) - Nonfood-Contact Surfaces (C) (d) Nonfood-Contact Surfaces. Nonfood-contact surfaces of equipment shall be cleaned at a frequency necessary to preclude accumulation of soil residues.

Observed cardboard boxes being used to absorb grease and hold flour debris from mixers. 511-6-1.07(2)(e) - Floor Covering, Mats & Duckboards (C) (e) Floor Covering, Mats and Duckboards. Mats and duckboards shall be designed to be removable and easily cleanable.

Observed employee belongings( cup and keys) stored with single use food boxes/containers. 511-6-1.07(4)(b) - Designated Areas for Employee Activity, located to prevent contamination of food, equipment, utensils, linens, & single service articles (C) (b) Designated Areas for Employee Activity.

1. Areas designated for employees to eat, drink, use tobacco products and electronic devices shall be located so that food, equipment, linens, and single-service and single-use articles are protected from contamination.

2. Lockers or other suitable facilities shall be located in a designated room or area where contamination of food, equipment, utensils, linens and single-service and single-use articles cannot occur.

Observed cheese received -from truck with an internal temperature of 50F for refrigerator and 34F for freezer- above 41F. Cheese was discarded and manager was advised to discard of other refrigerated items. 511-6-1.04(3)(a) - Temperature (P, Pf) (3) Specifications for Receiving.

(a) Temperature.

1. Except as specified in paragraph 2 of this subsection, refrigerated, time/temperature control for safety food shall be at a temperature of 41°F (5°C) or below when received. P

2. If a temperature other than 41°F (5°C) for a time/temperature control for safety food is specified in law governing its distribution, such as laws governing milk and molluscan shellfish, the food may be received at the specified temperature.

3. Raw eggs shall be received in refrigerated equipment that maintains an ambient air temperature of 45°F (7°C) or less. P

4. Time/temperature control for safety food that is cooked and received hot shall be at a temperature of 135°F (57°C) or above. P

5. A food that is labeled frozen and shipped frozen by a food processing plant shall be received frozen. Pf

6. Upon receipt, time/temperature control for safety food shall be inspected to ensure that there is no evidence of previous temperature abuse. Pf

Observed can opener containing black accumulation. 511-6-1.05(7)(b) - Food Contact Surfaces and Utensils - Cleaning Frequency (P, C) (b) Equipment Food-Contact Surfaces and Utensils.

1. Equipment food-contact surfaces and utensils shall be cleaned:

(i) Before each use with a different type of raw animal food such as beef, fish, lamb, pork, or poultry. It does not apply if the food-contact surface or utensil is in contact with a succession of different types of raw meat and raw poultry each requiring a higher cooking temperature as specified under DPH Rule 511-6-1.04(5)(a) than the previous type such as preparing raw pork followed by cutting raw poultry on the same cutting board; P

(ii) Each time there is a change from working with raw foods to working with ready-to-eat foods; P

(iii) Between uses with raw fruits and vegetables and with Time/Temperature Control for safety food; P

(iv) Before using or storing a food temperature measuring device; P and

(v) At any time during the operation when contamination may have occurred. P

2. Except as specified in paragraph 3 of this subsection, if used with time/temperature control for safety food, equipment food-contact surfaces and utensils shall be cleaned at least every 4 hours throughout the day. P

3. Surfaces of utensils and equipment contacting time/temperature control for safety food may be cleaned less frequently than every 4 hours if:

(i) In storage, containers of time/temperature control for safety food and their contents are maintained at temperatures specified under DPH Rule 511-6-1-.04 and the containers are cleaned when they are empty;

(ii) Utensils and equipment are used to prepare food in a refrigerated room or area that is maintained at one of the temperatures in the following chart and:

(I) The utensils and equipment are cleaned at the frequency in the following chart that corresponds to the temperature:

Temperature Cleaning Frequency

41ºF (5.0ºC) or less 24 hours

41ºF - 45ºF (>5.0ºC - 7.2ºC) 20 hours

45ºF - 50ºF (>7.2ºC - 10.0ºC) 16 hours

50ºF - 55ºF (>10.0ºC - 12.8ºC) 10 hours

and

(II) The cleaning frequency based on the ambient temperature of the refrigerated room or area is documented in the food service establishment.

(iii) Temperature measuring devices are maintained in contact with food, such as when left in a container of deli food or in a roast, held at temperatures specified under DPH Rule 511-6-1- .04;

(iv) Equipment is used for storage of packaged or unpackaged food, such as a reach-in refrigerator, and the equipment is cleaned at a frequency necessary to preclude accumulation of soil residues;

(v) The cleaning schedule is approved based on consideration of:

(I) Characteristics of the equipment and its use,

(II) The type of food involved,

(III) The amount of food residue accumulation, and

(IV) The temperature at which the food is maintained during the operation and the potential for the rapid and progressive multiplication of pathogenic or toxigenic microorganisms that are capable of causing foodborne disease; or

(vi) In-use utensils are intermittently stored in a container of water in which the water is maintained at 135ºF (57ºC) or more and the utensils and container are cleaned at least every 24 hours or at a frequency necessary to preclude accumulation of soil residues.

4. Dining counters and table-tops shall be cleaned and sanitized routinely after removing all soiled tableware and food trays shall be cleaned and sanitized after each use by one of the following methods:

(i) A two step method in which one cloth, rinsed in sanitizing solution is used to clean food debris from the surface and a second cloth in separate sanitizing solution is used to rinse;

(ii) Sanitizing solution is sprayed onto the surface and the surface is then wiped clean with a disposable towel;

(iii) If used for cleaning and sanitizing, single-use disposable sanitizer wipes shall be used in accordance with EPA-registered label use instructions; or

(iv) Other methods approved by the Health Authority.

(v) Food trays may be cleaned and sanitized the same as table ware.

5. Except when dry cleaning methods are used as specified under subsection (7)(e) of this Rule, surfaces of utensils and equipment contacting food that is not time/temperature control for safety food shall be cleaned:

(i) At any time when contamination may have occurred;

(ii) At least every 24 hours for iced tea dispensers including nozzles and consumer self-service utensils such as tongs, scoops, or ladles;

(iii) Before restocking consumer self-service equipment and utensils such as condiment dispensers and display containers; and

(iv) In equipment such as ice bins and beverage dispensing nozzles and enclosed components of equipment such as ice makers, cooking oil storage tanks and distribution lines, beverage and syrup dispensing lines or tubes, coffee bean grinders, and water vending equipment:

(I) At a frequency specified by the manufacturer; or

(II) Absent manufacturer specifications, at a frequency necessary to preclude accumulation of soil or mold.

Observed steak being thawed in still water in vegetable/meat washing sink. PIC placed item under running water. 511-6-1.04(6)(c) - Thawing (C) (c) Thawing. Except as specified in paragraph 4 of this subsection, time/temperature control for safety food shall be thawed:

1. Under refrigeration that maintains the food temperature at 41°F (5°C) or less; PF or

2. Completely submerged under running water:

(i) At a water temperature of 70°F (21°C) or below, PF

(ii) With sufficient water velocity to agitate and float off loose particles in an overflow PF, and

(iii) For a period of time that does not allow thawed portions of ready-to-eat food to rise above 41°F (5°C), or

(iv) For a period of time that does not allow thawed portions of a raw animal food requiring cooking to be above 41°F (5°C), for more than 4 hours including:

(I) The time the food is exposed to the running water and the time needed for preparation for cooking PF, or

(II) The time it takes under refrigeration to lower the food temperature to 41°F (5°C) PF;

3. As part of a cooking process if the food that is frozen is:

(i) Cooked as specified under subsections (5)(a)1 or 2 or (5)(b) or 5(e) of this Rule PF, or

(ii) Thawed in a microwave oven and immediately transferred to conventional cooking equipment, with no interruption in the process PF; or

4. Using any procedure if a portion of frozen ready-to-eat food is thawed and prepared for immediate service in response to an individual consumer's order.

5. Reduced oxygen packaged fish that bears a label indicating that it is to be kept frozen until time of use shall be removed from the reduced oxygen environment:

(i) Prior to its thawing under refrigeration that maintains the food temperature at 41°F (5°C) or less; or

(ii) Prior to, or immediately upon completion of its thawing, using procedures to completely submerge in running water as specified in paragraph 2 of this subsection.

Observed hole in wall adjacent to front hand washing sink and ceiling tile above walk-in cooler with black mold-like accumulation. 511-6-1.07(5)(a),(b) - Good Repair, physical facilities maintained; Cleaning, Frequency & Restrictions, cleaned often enough to keep them clean (C) (5) Maintenance and Operation.

(a) Good Repair. All physical facilities shall be maintained in good repair.

(b) Cleaning, Frequency and Restrictions.

1. The physical facilities shall be cleaned as often as necessary to keep them clean and by methods that prevent contamination of food products.

2. Except for cleaning that is necessary due to a spill or other accident, cleaning shall be done during periods when the least amount of food is exposed, such as after closing.

3. If present, playground equipment and associated areas shall be maintained in a clean and sanitary condition. In addition, a cleaning and sanitizing plan along with cleaning and sanitizing records for playground equipment and associated areas shall be maintained within the food service establishment for review upon request by the Health Authority. Further, such cleaning and sanitizing plan for employees to follow in the event of encountering vomitus or fecal matter shall be included and submitted at the time of permit application as specified in DPH Rule 511-6-1-.02(1)(c). Pf

Observed handwashing sink, next to vegetable sink, with no splash guard on side adjacent to vegetable sink. Please add another splash guard to other side of sink.

Observed pans with excessive encrusted grease deposits. Please replace place pans.

Observed grate/covering missing on floor drain/hole in front of reach-in freezer. Drain/hole must be covered to prevent the accumulation of food debris and pest attraction.

Observed dusty vents in women's restroom and rusting on vent in kitchen prep area.

Observed multiple TCS food items- chicken wings, ham, spinach, and provolone cheese out of temperature in the reach-in cooler.

Observed Quat sanitizer in 3-compartment sink below 200 ppm.

Employee health reporting agreement not provided

Observed food employee preparing food not wearing any form of hair restraints.

Wiping cloths not properly stored in sanitizer

Mold build up observed in between the walk in cooler fan

Acoustical tile observed in the men's restroom must be changed to vinyl. Backdoor is in bad repair. The door does not close properly. A follow up will be conducted on 2/5/24. The backdoor must be repaired to allow the door to self close.

Observed TCS food items in prep top cooler cold held above 41F. PIC replaced items with TCs food items from the walk in cooler 41F or below.